cpap hose holder headboard 3d models

A simple bracket to route a CPAP hose along the top of an IKEA Malm headboard. The back side that holds the hose is open to allow for easy removal. There are 2 version, one is designed to go around both sides of the headboard while the other is...

Headboard holder for ResMed AirMini CPAP machine. My headboard is a hair over 30mm wide so I modeled this for that. Note, the supports on my print failed so the picture is with a lot of glue while I wait for more black PLA to arrive from Amazon.

This is a simple hose holder for CPAP/BiPAP machines, for those that dont have a headboard to drape the hose to the mask over. Its made with screw holes or can be double sided taped to a wall or other surface. Most hoses will fit in the gap and have...

My CPAP hose likes to play hide-n-seek at night. ... This keeps the hose above my head so I don't get tangled up in it.

this is hang your cpap hose on the door after you clean it to dry it out. ... you do need to have supports on this design

This is a clip to hold a CPAP hose to a headboard while allowing it to rotate. ...It is sized for a ResMed S9 Climateline hose and a headboard thickness of 28mm.

CPAP headboard clamp for a 50mm thick headboard and 15mm CPAP tube with 18mm outer diameter. Materials: 1x 608 bearing for rotation 1x M5 screw to tension against headboard. To assemble: 1. Use the M5 screw to clean up the printed internal...

A swivelling clamp to attach the hose of a CPAP machine to the headboard of a bed. Instructions ****A note to MakerBot, we need a health section in the categories Print: 1 x Bed frame clamp (for headboard thickness of up to 30mm) 1 x Tube clip 1 x...

... the original was a bit too wide for our liking and I wanted to add a funny icon to the front - so I chose a gas mask, she loved it! ...I also Added an indentation on the back for self-adhesive pad A Remix of The CPAP Hose Holder by Mattwilsoncp16

This design evolves NailDRV's holder base for the popular Resmed AirSense 10 CPAP machine by providing two hose clamps/holders. One clip, on the side, from zimmer62's design, brings the hose out from the back to the front so it doesn't flop around...

Holds your CPAP hose and mask up on a hook, or whatever else you want up there. The end is tapered so you can pull the mask/hose off from below easily. ... Has a hole on top for the mounting screw.

A swivelling clamp with extension arm to attach the hose of a CPAP machine to the headboard of a bed. This is a remix / redesign of https://www.thingiverse.com/thing:47244 Other parts that fit the original will fit this also. Changes to the...

this hanger ist for CPAP and Resmed hoses.

My wife just got her CPAP machine and I printed this to help me manage the hose to help her sleep better. ...She uses N30i nasal mask so it attaches on top of the head.Very specific for our headboard but please feel free to remix it to suite your...

CPAP Hose support. Printed in PLA, but any filament type can be used. When sleeping my hose would keep on falling down and waking me up. Support is placed above the headboard of my bed. I can easily arrange the hose for various conditions. No...

This is a wall-mounted CPAP hose and mask holder. I designed an air slot in the extension with a built-in drain. ...This may work with an assortment of smaller face masks especially the nose cap ones.

One thing I’ve heard from several SA sufferers is that the hose from the CPAP machine can catch on your headboard or can wrap itself around bedside tables etc and just get in the way, so since I’ve just put some shelves up over my bed I designed...

I drape my CPAP hose over my headboard at night. After adding a hose cozy, I found that it would slip back down and then tug at my mask waking me up. So I made this clip on ring that would prevent it from sliding back down. What I've found is that it...

A CPAP hose and mask hanger for daily use in the bathroom.

A CPAP hose and mask hanger for daily use in the bathroom.

A visitor mentioned that they were looking for something like a CPAP Hose Clip to guide the hose near their bed, so I designed and tested this. The bore is 20mm, and the two parts go together with a paperclip bent through the hinges, and clipped...

... the clamp. I used OVERTURE filament because of it's strength tendencies over other PLA's. You can resize to anything you want, but right now it's designed for clamping standard size cpap hose ends. ...I believe it's around 29 mm.</p> Category: DIY

... off at night, thus the clamp. I used OVERTURE filament because of it's strength tendencies over other PLA's. You can resize to anything you want, but right now it's designed for clamping standard size cpap hose ends. ...I believe it's around 29 mm.

I adapted an old CPAP hose as a vacuum attachment for cleaning around my work area and getting where the full size vacuum wont go. This plugs into most standard vacuum cleaner hoses as an attachment. Print as oriented, no supports needed. Cut the...

I adapted an old CPAP hose as a vacuum attachment for cleaning around my work area and getting where the full size vacuum wont go. This plugs into most standard vacuum cleaner hoses as an attachment. Print as oriented, no supports needed. Cut the...

Just a basic CPAP hose hanger. The two ends of the hose clip into the sides. Note: This is not to hold the hose when sleeping. I use this to hold the hose when I fill it with cleaning solution and leave it to hang to sterilize. I didn't see...

Yet another CPAP hose clamp. My wife needed a 90 degree clamp which I didn't find available on thingiverse yet. So I made a set of different types. Attach with double-sided sticky foam, or 3M Command Strips. ... Enjoy!

This is a 22mm swiveling hose connector that I made to connect my CPAP hose to my face mask. It could also be used to connect two hoses together. ... I have printed it successfully twice and I use it personally so I can testify that it works well.

Air flow is adequate for one CPAP hose to move with the head on a 3018-size CNC machine, while the other hose is handheld to pick up clumps of swarf and cuttings that collect around the machine. ... A hole is provided for a M5 bolt or screw, if you...

CPAP hose clamp to suit a resmed airsense hose - I think this is a pretty common hose size, so should suit other brands just fine. I've designed it to take a piece of double sided velcro to fully secure the hose, but it also works fine without it. 3M...