cr 10 control box replacement 3d models

Remastered limbs crafted by Shift-31 showcase a subtle enlargement. ...The controller now boasts an increased span of 126.5 millimeters, subtly repositioned to enhance the user experience.

This is a replacement for the feet on your Creality CR-10 or CR-10S printer (assuming the frame mounts are the same - I use it on my CR-10S). In theory, these should make your printer slightly quieter than the stock feet, although I didn't test the...

I designed this to replace the noisy stock 50mm fan. A 60mm Noctua fan won't fit under the PSU without some bigger modifications, so I created a dual 40mm fan bracket instead. ... I also moved the fans slightly to the right, now blowing air directly...

I recently purchased a Stronghero3d filament and discovered that the roll drags on top of the controller box when using the stock filament holder. This problem doesn't seem uncommon after looking around online, many brands use larger filament rolls.

The fan mount is adjusted upward to accommodate larger and more powerful 40mm fans.

I upgrade the entire filament detection system because it's not securely attached to the machine.

This is a replacement foot for the control box (under the arm cuff). ...The foot is attached using self taping / coarse threaded screws, take care when tightening these screws as the walls of the aluminum case are thin and could easily be stripped due...

A straightforward design for a 120mm fan holder that interfaces with the CR-10 control box, accommodating two fans of the same size and featuring a discreet cable management slot to simplify installation - no additional supports are required.

### 3D component list: Model name Description CR-10_Cablebox_t-nut_4connector_16mm_v1.stl t-nut box with four holes (CR-10) CR-10_Cablebox_t-nut_5connector_16mm_v1.stl t-nut box with five holes (CR-10S) CR-10_Cablebox_t-nut_6connector_16mm_v1.stl...

... a position that allows all original cables to be used. ... only the 2 original box fans are not used the kit https://www.thingiverse.com/thing:2747280 I used other feet higher to give space to the motherboard https://www.thingiverse.com/thing:3024887

A customized CR-10 cable box with a dual-row connector layout, inspired by FiReDoGGi's suggestion. To enhance versatility, I've created two variations: one featuring holes for clips and another with holes for T-nuts. ...A transparent top complements...

Here's a simple box design solution to prevent the Cr-10 power supply from toppling over when using the reel holder mounted to the top. ...This design also serves as convenient storage for the various tools you use on your printer.

Design to adapt the CR-10 filament sensor for BMG on an Anet ET4.

I made this box which can mount the switches: http://a.co/frzqefa it screws on to the CR-10 frame with one T- Slot Nut 5mm T-slot nuts. http://a.co/eIZccJN M5-0.80 x 12MM Button head socket cap screws, allen head. ...http://a.co/3VrgGjZ easy to print,...

I designed this switch box around the cr-10 stock Z-axis end stop switch to work seamlessly with Octoprint. Originally removed from my cr-10 to install the ABL auto leveling sensor, it's now being repurposed as a filament run-out switch. The T-like...

Here is a rewritten version of the text: Custom LCD and Control Knob for Creality Ender 3, Ender 3 Pro, and CR-10 Models. ... Remixed from Original Designs by Guppyk (Thingiverse: #4204606) and Inuit (Thingiverse: #3611103).

To improve stability, I reinforced the side rails by installing additional support brackets.

This is my very first remix and my first thing in general. I customized the original rails to accommodate larger size bearings, 608, which I had on hand. As a total beginner, this isn't a masterpiece, and it's not even fully complete yet, but it...

Add 20 inches to feet and eliminate plastic caps from the bottom. ...Based on https://www.thingiverse.com/thing:2767439, created by spaxi.

Just a simple offset block so you can use TopHatWaffle's mod with Mk42Workshop's Z-Braces. You can probably just mirror the screen mount and case files, but I liked having everything on the left side of the printer because that's the side with the...

Revised the build to exclude standard fasteners. ...Refer to the prototype for specifics; supplemental reinforcement not required.

<p>Remixed the original to except the stock screws. ...See original for details, no supports needed :)</p> Category: 3D Printer Parts

Since swapping out my extruder for a Direct Drive model, I've secured a spot to attach the Buck converter directly onto my CR-10, allowing me to power the LEDs at 12V smoothly. ... I created this accessory to complement...

I made this enclosure that holds the switches: http://a.co/frzqefa It securely attaches to the CR-10 frame with one T-Slot Nut. ...5mm T-slot nuts are needed, available at: http://a.co/eIZccJN M5-0.80 x 12MM Button head socket cap screws, allen head...

To mount this upgrade on my Creality CR-10, I browsed Thingiverse for a suitable box. The idea to mount it to the frame of the machine like the "OctoPrint Raspberry Pi Rig 3.5 PiTFT Touch Display - Mod for CR10s" by Nosferatie was appealing. The...

Ender 10S Upgrade Power Supply Control Unit Stand Best Creality CR-10/S/V2 Upgrades & Mods elevates the control unit about 2.8 inch - 7.3 cm helps in good unit ventilation and better cooling easier access to the sd card avoid grounding electric...

... this project has been a delightful experience! The end result is impressive - exceptional temperature control and a remarkably quiet unit. ...For more information, visit https://www.thingiverse.com/thing:3369882 to see the Raspberry Pi Mount.

This is to complete my set of knurled knobs for the Creality Ender 3 / CR-10 / Ender 3 Pro (extruder knob, Z-axis knob, and finally control knob - I like them all in the same design). Simple, stylish, ergonomic. Printing. Printing should be really...

CR-10 S5 AC Hot Bed Control Cabinet with Thermal Protection (Home Assistant) CAUTION: It is highly recommended to have a qualified person handle any electrical work. Version 1: 8 Amp IEC Connector - suitable for smaller heated beds that draw 8 amps...

I made to get rid of that annoying external box. ... https://www.youtube.com/watch?v=xjX0AxSESOk