cr 10 e3d v6 upgrade

This is my attempt at creating a custom mount for my Geeetech G2S printer to utilize dual E3D V6 hotends with a Bowden connection. I tried several other plates on this site, and while they are excellent designs, using them would cause my arms to no...

This is a basic clamp style mount to mount an E3D V6 hotend with the round clamp style mount to the x axis carriage on the CR-6 SE and Max printers. This will only work if you completely delete the factory hot setup and only use the carriage. ...I...

A variant for a user that has a CR TOUCH and E3D hotend

To assemble this one you'll need: A machine capable of printing good-quality ABS parts 10× M3 hex nuts 4× 16-20mm M3 bolts (to mount the cage to the effector) 4× 8-25mm M3 bolts (to assemble the cage) 2× 6mm M3 bolts (to install magnetic probe...

I haven't found yet a satisfying project to upgrade the hotend on my Tarantula Pro so, after some searches and modifications, I've come up with this. The fan shroud was fixed so that the cooling fans are centered perfectly. ... If you want to learn more...

I haven't found yet a satisfying project to upgrade the hotend on my Tarantula Pro so, after some searches and modifications, I've come up with this. The fan shroud was fixed so that the cooling fans are centered perfectly. ... If you want to learn more...

This upgraded version 2 is significantly more streamlined, allowing for seamless installation and effortless removal of the hot end in case of any problems.\r\n\r\nDuring printing, position the model so that the base rests on the bed, while the...

This is a remix of the fan duct in order to replace the stock MK8 hotend by an E3D REVO CR (which is a bit wider). The other parts can be downloaded from the source thing. ... I haven't received my REVO CR yet, so this hasn't been tested.

2021-08-15 Updated E3D_V6_Threaded.stl for better height adjustment, otherwise the official fan duct is too high ------------------------------------------------------------------------------------------------------------------------- This is my...

I bought the E3D V6 clone (1,75mm, 24V, Allmetal) from Trianglelab: https://www.aliexpress.com/item/32888737278.html Installation: • Install Community Firmware Alpha 4...

It's a version 2 mount for E3D V6 Volcano Titan Direct Drive Extruder, right sided, designed to replace original X axis aluminum mount. This design only works with E3D Titian right extrude setup. You may need to complete the set with another left...

26.5.2023 update bigger cooling hole and fan 5015 support 23.5.2023 Update bigger cooling tube Hello Together, I bought the Creality CR-M4 and found the same defects as seen in various youtube videos. (Disaster at the price) It's a real pity, the...

*30.05.2021 I replaced the files with updated version:* - Thicker backplate (2mm -> 3mm) - Thicker heatsink hilder - Two holes in the wire hilder plate for convenient cable tie use This is a single piece adapter to upgrade your Creality CR-10 or...

The E3D Clone hot end mounts a lot lower so the stock part cooling fan ducts blow on the hot end and not at the nozzle. This uses the stock fans and mounting and you replace the existing fan duct. Check the photos for the suggested print...

Touch MI Support for "CR-10 Heavy Duty Customizable Modular E3D V6 Mount Volcano 5015 ABL" by Chito.

-5015 Volcano Fan Duct Bracket for Tornado Mount -5015 V6 Fan Duct Bracket for Ender-2 mount Update 9/8/2018 -Confirmed by OneEyeDesign that it works on a CR-10. -Uploaded Fusion360 File. Warning: Use it at your own risk. It is VERY MESSY! ... Update...

... for Ender-2 mount have been uploaded. **Update 9/8/2018** - OneEyeDesign has confirmed that it works on a CR-10. - The Fusion360 File has been uploaded, but use it at your own risk; it is VERY MESSY! ... **Custom probe location:** X= -30 Y= -5

Additions: - **Toolless accessory mount** - Pen holder - Vinyl cutter holder Instructions --- **Required hardware:** - M3 hex nut - x2 - M3 x 6 counter sunk - x2 - M3 x 8 counter sunk - x1 (can be replaced with M3 x 10, bracket assembly left most...

As there is no way to adjust the air duct height - make sure to assemble your hotend as per E3D instructions and have the nozzle not tightened against the heater block but with a slight gap, as the duct was designed with that in mind.You need to use...

Thanks to martin_au for this fantastic design. I downloaded his files and printed all of them in PetG, where they fit perfectly. But I needed a bit more cooling, so I remixed the fanduct part to accommodate two cooler fans - one for the hotend and...

I'm grateful to martin_au for this fantastic design. After downloading his files, I printed all of them in PetG and they fit together perfectly. However, I needed a bit more cooling, so I modified the fanduct part to accommodate two cooler fans -...

Cr-10 e3d hemera (bowden) direct extruder mount

Compact Support System Operator: Ventilation Fan for Ceramic V6 Volcano on Creality CR-10.

Get READY TO ROCK with your CR-10 3D printer and elevate it with a high-performance E3D Titan extruder paired with a V6 or Volcano hotend. This upgrade also includes a mounting spot for a popular 5015 blower fan, making it easy to boost airflow. All...

fan 3010 2 pcs E3D v6 1 pcs

fan 3010 2 pcs E3D v6 1 pcs

I also included a mount for the probe that comes stock with the CR-10, it also mounts onto the same spot as the hotend mount mounts to the printer frame! Prints with no support! Print instructionsUnassociated tags: direct drive, e3d v6, PLUS ULTRA,...

MGN12H V6 E3D BMG Extruder

This is a mix for an E3D Titan Direct Extruder with V6, ABL and laser mount from existing sources designed specifically for the CR-10.\r\n\r\nThe mix comes from:\r\nhttps://www.thingiverse.com/thing:2991385 (includes detailed building...

I'm thrilled to share my latest creation - a customised e3D V6 mount that's specifically designed for the CR-10 Heavy Duty. This mount is all about flexibility and adaptability, much like the printer it's built for. With its modular design, you can...