cr 10 fan upgrade 3d models

This is a sleeve with the fan blades that fits 40mm cooling fans with a wider center diameter. Refer to the dimensions in one of the images to see if it fits your fan. You're supposed to cut the original remaining blades and slide this sleeve into...

I busted the original ender 3 fan blades with my tool (and I used DanielMitchel's design to fix it) but then I replaced it with a much quieter chinese fan:...

Here's what I did: - Positioned the cover slightly farther away from the fan - Increased clearance at the top cap for smoother airflow - Incorporated 8 lateral vents to facilitate effortless air circulation The uploaded model includes two simplified...

This design mounts to the lower hole of the stock fan shroud instead of using heat sink screws, allowing access to the hotend with just one screw. This is a rough modification with the following changes: - Add a bracket for the lower left fan shroud...

Additionally, I removed the hot end fan mounts as they caused fitment problems with the heater wires. Instead, I'm using a standalone piece from dhien2's design to mount the hot end fan. ... EDIT 2: I created an alternative version without the part...

To keep things tidy at the origin point, I use three clips to secure the bed.\r\n\r\nThe depth meter I sourced from Aliexpress can be found here: https://goo.gl/tWTAa6.\r\n\r\nFor the construction of this tool, I used M3 screws:\r\n4 short ones - 6mm...

The concept is that it will obstruct some airflow coming from the bottom of the fan, thus not cooling the heater block, and you might even be able to run without a blanket on your hot end. ...If you're 3D printing it with ABS recommended, although with...

I'm using a modified version of the original hotend cooling design from Thingiverse (2751027) on my Ender-2 with a 40x20 fan, and pairing it with an extremely powerful print cooling system for a 60x15 fan setup. I also added a cover grid selection...

All screws used are from either the original CR10 bottom plate or standard computer screws for fan installation. After weeks of designing, this project has been a delightful experience! The end result is impressive - exceptional temperature control...

You can connect it directly to the board with internal fans or use a phone adapter, taking advantage of the hole on the right side for a standard switch. If connected to the board, you can mirror the left cover panel and utilize it for the right...

I redesigned this from the Imagine That Titian/Atlas cooling fan, which I've been utilizing for some time now. The only aspect that didn't sit well with me was the oversized opening of the blowers, resulting in a significant portion of the cooling...

I designed this Anti-vibration Bar specifically for the Double Fan 5015. Simply insert two points of glue into the hollows at each end and secure it in place. My initial design was basic, yet my ultimate goal is to eliminate all vibrations. ... —...

Fan shroud for the Titan Aero with a volcano hotend. Print with platform supports only! The holder is for the Titan Aero with pancake stepper. One version is for the use with a heatsink. ... Fusion 360 model: http://a360.co/2Btdon1 Category: 3D...

I increased the thickness of the bolt stand-offs as I was finding the originals to be too thin, prone to breaking under accidental over-tightening of the mounting bolts - a common problem also faced by the stock fan duct. ...This revised design is...

These lightweight hot end fan ducts produce negligible mass forces, making them effortless to install. Simply utilize the screws from the original head cover or vents, replacing the 40mm vent with a silent one if desired. ...The result is outstanding...

... minds at CNCKitchen. ...Check out their remarkable creation on Thingiverse at https://www.thingiverse.com/thing:2756792. Perfectly tailored to accommodate a 40mm fan, this mounting system provides seamless integration and effortless installation.

... attached with screws from underneath. If you're worried about stability, take your time, but trust that the end result will be worth the extra effort. For a fan silencer, check out this clever design: https://www.thingiverse.com/thing:3597687

Fan shroud for the Titan Aero with a volcano hotend. Print with platform supports only!</p> <p>The holder is for the Titan Aero with pancake stepper. ...One version is for the use with a heatsink.</p> <p> <figure class="media"> <oembed...

Remix - really like this fan duct by EdMouhahaha, so I've tweaked it a little : a) Extended the nozzle tips so that they touch the heat bed, should be easier to print without supports b) Added a another variation with the front duct removed - so that...

The factory hot end housing that creality uses on several of their models is fine but the design doesn't really direct the air from the cooling fan to any particular place, it just kinda blows air all over everything. This causes air to blow down...

I've created a new module for Raspberry Pi, allowing you to use one 120mm fan and a Raspberry Pi instead of two 120mm fans. The Raspberry Pi 3B slides over the mounting points and you can mount two LM2596 with two M3 bolts. I haven't printed or...

This remix is designed for E3D Volcano type hotends, with a fan size of 40mm.\r\n\r\nTwo versions of the fang are included: one that is slightly shorter to provide more clearance under the bed and another, longer version (medium), which directs...

... surface has been flattened. - The fan inlet has been reworked for better performance. - The back mounting arm has been modified for improved printability. - Some model issues have been fixed. ... Suggestions for further improvements are welcome.

The basic fan mount design is virtually identical to the original one that came with the printer, but it's less electrically conductive! This version is lighter in weight and offers more color options! Designed using Blender. *Removed - Fanmount2...

Virtually the same basic fan mount that shipped with the printer just not as electrically conductive! Lighter weight and more color options! Created with blender. *Deleted - Fanmount2 is an updated version of Fanmount and works with Partcooler2...

I also added some fans and a thermistor, soldering all components according to the provided schematics in the swappable hot end design. A spare heater element was used, but unfortunately, it turned out to be a 24V version that didn't reach the...

Are you browsing Thingiverse in search of a Creality CR-10 upgrade? Well, look no further! This is the most comprehensive upgrade ever! The advantages of this upgrade are:\r\n\r\n-Ease of use guaranteed \r\n-Say goodbye to sore thumbs (more leverage...

This part is specifically designed for attaching the stock filament runout sensor of Longer LK4 Pro to a dual drive extruder upgrade kit.\r\n\r\nThe upgraded aluminum dual-gear pulley dual-drive extruder kit can be found here:...

... had to find something compact that worked with BLtouch and this is working out for me so far. This part was 3D printed on an MP Mini Delta because I had to replace the hotend on my Eryone Thinker SE (~CR-10 clone) and had to use my backup printer.

Are you scrolling through Thingiverse searching for a Creality CR-10 upgrade? Well, look no further! This is the most ultimate upgrade ever! The benefits to this upgrade are: -Ease of use -No more sore thumbs (more leverage on arm) -Print flexible...