cr 10 v2 upgrades 3d models
448763 3d models found related to cr 10 v2 upgrades.
thingiverse
The CR-10 V2 already comes with a super quiet stepper controller but the stock fan included are very loud so I replaced it with all Noctua fan. Things that I used. - Noctua NF-A6x25 FLX x2 - one for PSU and one for the casing - Polulo...
cults3d
Ender 10S Upgrade Power Supply Control Unit Stand Best Creality CR-10/S/V2 Upgrades & Mods elevates the control unit about 2.8 inch - 7.3 cm helps in good unit ventilation and better cooling easier access to the sd card avoid grounding electric...
thingiverse
I´ve constructed an upgrade for the bad filament holder of the Creality CR 10 2. The distance between the ball bearings can be adjusted with a crank. The main holder is fastened with a large nut. Use two ball bearings with the following dimensions:...
thingiverse
The CR-10 hotend seems to work flawlessly, while myself and others I know have had numerous problems with the Monoprice factory hotend. No new hardware required. Simply print the backplate with supports with columns facing up, the faceplate...
thingiverse
The CR-10 V2's Meanwell PSU is 24 volts so it will require a Buck Converter (or other method) to provide 12V for the new fan. I have split the bottom cover in two parts for ease of printing. When torqued down all is tight. The fan cover is a...
prusaprinters
CR-10s Pro V1, CR-10s Pro V2 and CR-10 MaxMaintenance, trouble shooting and upgrade guide …now following some facebook forums and other chatrooms it seems, that there is always a core set of things which are repetitively asked, so I decided to...
thingiverse
Parts for better airflow when changing out fans on the CR-10. ... Read more about the designs and how to install them here: https://fdproj.wordpress.com/2018/01/22/cr-10-silent-new-fans-vibration-dampers-and-design-upgrades/
thingiverse
This is a Remix spool holder for the Creality CR-10 or CR-10 V2 that simply clips on to the X-axis stepper motor mount.
thingiverse
- Removed the part for the flexible part since I can't print that material - Added hole down the middle so I could screw in the original rubber feet from my CR-10 v2. Requires a M5 nut to be inserted into the leg - The rear foot has a long...
thingiverse
Standalone Gehäuse für den CR-10 V2. Netzteil und Board passt alles Plug & Play, nur die Kabel vom Zuleitungsstecker zum Netzteil müssen verlängert werden. Es ist für einen Raspberry Pi, 2x Relais und einen Stepdown geplant. Von mir...
thingiverse
Updates: 8/8/2022: Added version of BLTouch mount with cable holder rod - - - Здесь представлены изменённые детали из [K3D Printhead for Ender-3/Aquila/CR-10](https://www.thingiverse.com/thing:5172583). Включает в себя: 1) изменённую версию...
thingiverse
... move the tension spring screw to the left, while Cover 5 narrows and moves the bowden tube fitting to the left. Knob in image is from: https://www.myminifactory.com/object/manual-filament-feeder-knob-mod-for-cr-10-and-other-bowden-3d-printers-52492
thingiverse
Filament guide for the CR-10 V2 https://www.buymeacoffee.com/jschaftenaar
thingiverse
Z stopper mount for new users of the CR-10 V2. ...Helps to lower the bed to aid in setup.
thingiverse
dbl pully for the cr-10 v2 attachs to runout sensor made for the 608 bearings but included a file for use without but it binds alot
thingiverse
... . ... I just change the slot USB key and added a pliers slot too. Print Settings Printer brand: Creality Printer: CR-10 V2 Materials: PETG Temp settings: Buse = 240°C Bed = 80°C Rafts: Doesn't Matter Supports: No Resolution: 0.2 Infill: 30%
thingiverse
... i obtained from Joseph Yarger, i have permission to share:) This just mounts directly onto the extruder housing no screws needed. ...I modified his design to not interfere with the fans exhaust on the CR-10 V2. Its more low profile as a result. ...
thingiverse
I needed a tool holder and as far as I can tell there really wasn't anything for the CR-10 V2 specific tools. This is designed for a 5/8 thick table top using Fusion 360. This is my first upload I'm still learning the ends and outs of fusion 360.
thingiverse
Filament guide for the filament sensor on Creality CR-10 V2. I noticed that retraction was causing the filament to be shaved slightly at the metal input guide on the filament sensor. It wasn't impacting prints but it was making a mess of my work...
thingiverse
Used these things of MrMartiniMo: 4x PC_arm1 1x PC_arm2 1x PC_base1 1x PC_base2 5x PC_knob 1x PC_washer Used these things of jimmysinkers: 1x caseFront 1x caseBack_picam_v2 Use this of me: 1 x caseBack_picam_v2 hook 1 x Mount for CR-10 frame Buy and...
thingiverse
I used this: https://www.thingiverse.com/thing:4495009 The legs i used: https://www.thingiverse.com/thing:2786225 The LCD mount i used: https://www.thingiverse.com/thing:4602730 You can also use this the LCD mount from this mod:...
cults3d
Support for raising the 125 mm wide main block of Creality CR 10 3D printers and derivatives.
thingiverse
This is the second version of my direct drive spool holder for the CR-10. This new design has a bar that you put on top of the spool holder. With the bar the poles can't split apart anymore, which was a problem with the V1. ...If you have any questions...
grabcad
This is a home made model of the Creality OEM main board v2.5.2. The position of each connector and driver may have very small variation but it's almost that. I built this model in order to relocated the control unit under the structure and have a...