cr 10 v3 extruder upgrade 3d models

This is just the E3D Direct Drive extruder cover of the Creality CR-10 V3. ...The original part is a transparent injection molded piece, which breaks easily if you tighten the screws a bit too much.

MDG CR-10 V3 UPGRADE PROJECT Official Site: **[MAKERS DEVELOPMENT GROUP](https://www.makersdevelopmentgroup.com)** MDG CR-10 V3 Project Link: **[MDG CR-10 V3 UPGRADE PROJECT](https://www.makersdevelopmentgroup.com/cr-10upgradeproject)**

Upgrade for CR-10 with BTT TFT35 new 3D printer for small money.

This is an upgrade for CR-10, It will allow these printers to print with flexible filament more reliably using a PTFE insert to close the gap in the extruder that normally allows TPU to get jammed. ... I used this video as tutorial:...

Holds the black cable that hangs over the extruder.

I recently bought myself a CR-10 V3 and the first thing I noticed was the wires for the extruder will touch and drag on the hot bed and catch on the print. This was really not thought through on Creality's side. ...This is just a quick print that will...

Hello, this is a cover that fits cr10 v3 with direct titan extruder. ...print strong supports around nuts part.

----------------------------------------------------------------------- In order to print with flexible filament I wanted to upgrade my extruder using joshvv's part design. But when I tried to insert a piece of my old 4mm diameter PTFE tube I...

Designed this clip to hold the Creality Laser to snap on directly to the direct drive extruder on the CR-10 V3 E3D Direct Drive Extruder Printer. There are two version one with holes and one without. ...The holes are to direct mount the D-B500F...

... print bed, I decided it was time to sort a solution. ...This thing fits over the rear of the stepper motor with no determent to heat and allows you to cable tie the cable out of the way of the heated bed plus also the filament going into the extruder.

Since I changed to a direct drive set-up but wanted to keep a cover on the extruder I developed this one. When I snapped on the original, I didn't like the angle and felt the it would work better with the filament as a straight drop. If anything it...

This is my new upgrade for my printer hope you guys like it :D and enjoy it too :D. List component : 1. rubber legs M8x1.25 x40 2. washer IO 06mm, OD 16mm 3. ...M4 from the original leg of printer video : https://youtu.be/IR6tR9reZbs

I made this frame because I wanted to slowly migrate the contents of my CR-10 control box to underneath the printer. I am using 2040 aluminum extrusion. I cut 2 pc for the entire length of the "Y" axis and 2 pc for the entire length of the "X"...

... la v2 y listo A disfrutar. Pick up cable from the extruder of the cr-10 v3. I couldn't find anything and designed this piece. It is very fast and effective. ...With two screws it is attached to the extruder hole of the v2 and that's it To enjoy.

CR-10 Extruder upgraded replacement.Aluminum MK8 drive feed 3D Printer extruders for Creality Ender 3, CR-10, CR-10S, CR-10 S4, CR-10 S5

CR10 Extruder TPU Bracket: Added radius by design rules for 3D-printing: + better flow of forces + decreases shear forces by bigger area on weak Z-Layers-adhesion Original designed by @joshvv https://www.thingiverse.com/thing:2144277

I was always annoyed with the control box being off to the side of my new Creality CR-10 V3 printer, so I decided to do something about it. The control box now sits underneath the printer and really cleaned up my workspace a bunch by giving the...

CR-10 extruder suspension. Mounted with vibration dampers, to reduce the noise. Filament guided away from z-screw. ... Will also work with the stock extruder.

Reupload of other's files to try and get as STEP instead of SLDPRT - all credit goes to CR-10 Extruder

Four in one CR-10 Extruder Basis Plate New Extruder Plate for the CR-10 Printer. - New Design to print flexible Filament without PTFE Tube - Dust Cover with window (you can open and/or remove it without taking the Filament out of the Extruder) -...

This is a spacer to increate the spring force on at CR-10 Extruder. I had intermittent under extrusion from slipping filament. ... Some people report having better fit using 110% scale.

A simple knob I designed for the extruder of the CR-10. ... Might work for some other printers as well, but it's the only one I have to test it on.

UPGRADE SPOOL FOR ENDER CR 10 V3 ENJOY

Print Settings Printer brand: Creality Printer: CR-10S Supports: Yes Resolution: .2 Infill: 50% Category: 3D Printer Extruders

Updated Version so you can use the CR-10 Factory Stepper Motor . ... Kinda of a remix of https://www.thingiverse.com/thing:2494642

After upgrading my printer with a BMG clone extruder, the Z rod was hiting the extruder. I made this bracket so it turns the extruder and steper 90º. Also left some space to add a cooler on the steper. ...As you can see on in the pictures.

28.05.2019 Für den Fall, dass das Teil beim m6 Gewinde immer wieder abbricht: Ich habe nun das File "CR-10 Extruder Coupling.stl" hinzugefügt. Dieser muss mit einem abgeschnittenen Nozzle Throat (inklusive inneres Teflon) befestigt werden. Dieser...

... of extruder cooler - you will need 2x or 4x 20mm M3 screws for this part. Spool Holder Upgrade kit Print this as a solid tangle free upgrade for stock CR-10 spool mount Print 1 Nut, and 1 NutCut to attach spool holder to stock spool base. ...

It is compatible with the filament guide that a lot of users know and use (search for "Creality CR-10 Filament Guide", Thanks to Greg191134). It is essential to print at 100% infill, and layer 0.1, because of the fitting between the lever and the...

This is an extruder-upgrade for the printers like CR-7, CR-10, Ender 2, Ender 3. The PTFE insert is held by an additional extrusion. It closes the gap in the extruder that normally allows TPU to get jammed. To optimize the function, you can also...