cr 10 v3 extruder upgrade 3d models

Creality CR-10 users can upgrade their printing capabilities with the Titan Extruder installation guide found at https://www.thingiverse.com/thing:2274222 or alternatively, check out https://www.thingiverse.com/thing:2474855 for further instructions...

Hello, This is a direct extruder upgrade for your Creality CR-10. It's incredibly simple to assemble and incredibly light. To build this extruder, you'll need: * Your existing extruder * An E3D V6 hotend or an alternative (we won't judge) * A...

###Items Required: 8mm OD Rod 22mm OD x 8mm ID x 7mm High- Bearings x2 1x Raspberry Pi 3 Modell B - Quad-Core Processor / 1GB RAM WiFi Bluetooth on Board 1x 8GH Micro SD card I wasn't happy with the CR-10 v3 spool holder so I designed my own because...

Relocation of the Creality CR-10 V3 Machine's Runout sensor to the middle of the top track. I designed this to work with the stock sensor and hardware. It is also designed to go with either the stock spool roll to improve the angle that filament is...

This is a universal mount that fits onto the CR-10 V2 and V3 stock hot end housing.intended for remixes as it allows you to easily attach anything to your printer in seconds.it snaps on over the housing requiring no tools or screwsand once in place...

There are some alternative solutions for this already but I wanted a simpler design so this Cable Holder (for the upgraded metal extruder for Creality Ender 3/5) simulates the original cable holder on the plastic extruder that comes with the printer....

I was looking for squash ball feet that I could use on my CR-10 v3 and came across the feet that bandou made. I printed one and found that although they would fit in 3 of the 4 corners, they would not allow the v3 to be high enough to clear the Left...

The Turbine-Style Extruder Rotation Visualizer for the Creality CR-10 3D Printer.

Add some flair on top of your CR-10's extruder to make printing a blast!

Problem The original 110mm tall runout sensor mount that came with my Ender CR-10 V3 was giving me a few issues: The filament seemed to be binding The connector running from the sensor to the x carriage was pulled tight when the z-axis was homed The...

Original was too high for my CR10 V3 so the extruder was ramming into the hotbed. Not great :D So I made this adjustable one with plenty room for fine tuning. It's a small part so 100% infill shouldn't eat too much filament while it will provide...

This is for the CR-10 Version 3 Printer that has a direct drive "Titan" extruder. The original filament angle that comes off the spool into the runout sensor has failed several prints for me so I figured on designing this. It sits on top but moves...

A replacement arm for Creality extruders. The bearing is supported on the top and bottom, so it is stronger than the stock arm. I lengthened the arm for better leverage. ...I extended the part that holds the spring so I could add spacers to increase the...

eSun PLA+ Filament: https://www.bastelgarage.ch/pla-filament-1-75mm-schwarz-1kg-esun Original Creality BL-Touch retrofit kit : https://www.bastelgarage.ch/cr-10-v2-bltouch-auto-bed-leveling-sensor For the do-it-yourself alternative you need the...

Add a fun twist to your prints by placing a creative accent on top of your CR-10's extruder.

Install a customized part on top of your CR-10's extruder to give it a unique twist.

This versatile extruder is perfectly suited for use with the CR-10 printer when paired with a Vulcan block.

When I upgraded to the Titan Extruder on my CR-10, I found that my original filament sensor stopped working because the new extruder's unique design demands a specific orientation due to its cleverly engineered lever and threaded lead screw. ...To...

This is the cover for the Y switch for the cr10 v2/v3 , the .stl comes from creality.

Slight tweak on the TinyMachines CR-10 V2 BLTouch mount they talk about in this video: https://www.youtube.com/watch?v=gHQ4WroVD6k For my use case the screws that came with my BLTouch were shorter than what the TinyMachines folks show in the video so...

Created this mount for my new V3 camera. ... Should just snap into place and be a slightly snug fit so it stays in place.

Created this mount for my new V3 camera. ...Should just snap into place and be a slightly snug fit so it stays in place.</p> Category: Camera

CR-10v3 Camera mount customized with OnShape to allow for custom camera mount with square hole and slimmed curved profile. ...Wanted a friction fit instead of messing with my bed screws.

Snoopy extruder knob for CR-10 Remix of https://www.thingiverse.com/thing:3627473 with CR-10 base. Like something I've made? Please consider supporting me. ... PayPal: peterr211mm@yahoo.com

Screw in the groove mount adapter, place the extruder halves over the groove mount, tighten to the motor, tighten the mount to the carriage, done. Note: it is not required but I recommend heating the hotend to printing temp, loosening the nozzle a...

Cr10 v2/v3 X Carriage Model. This model is not 100% exact as I am modeling based on my own measurements, but it is very close. ...Mounting holes line up very well and I used it myself to design a custom hotend mount.

This is just a Remix of my better spool holder for the Creality CR-10V3, It is the same top mount as my last one just runs with one arm and a longer spool roller. For the minimalist out there that wants less parts to print and half the time to print...

Whether you're a seasoned 3D printing enthusiast or just starting out, the Creality Ender 3/Pro and CR-10 Extruder System is an ideal choice for achieving professional-grade prints in the comfort of your own home. Its robust design, advanced heat...

Preferring the reliability of a full metal hot end, I decided to convert it.\r\n\r\nWith approximately 61mm of Capricorn tube, this upgrade is remarkably straightforward!\r\n\r\nI printed with Nylon, concerned about potential long-term heat issues,...

Adapter plate vor mounting your BTT SKR MINI E3 V3 in your Creality CR-10 V3 control box. ... I can also supply a step file vor easy editing, just contact me.