cr 10s filament sensor 3d models

This is a REMIX of https://www.thingiverse.com/thing:2935674 "New CR-10s Filament Sensor Housing Assembly" made by David Levy https://www.thingiverse.com/davidaelevy , but since the search in Thingiverse is so crappy, it's been impossible to upload...

What I like about his design is that it fits the CR-10S' stock filament sensor switch perfectly and his filament guide holes are lined up so well that it doesn't require any fishing when loading filament. I used everything except Mr. Falkenstein's...

I redesigned the setup so you can install the CR-10s stock filament sensor directly. ...Secure the cap with zip ties or reuse the original screws from the stock sensor housing for a seamless integration.

... no longer fit as expected, so I made a cut-out in one corner and now it fits perfectly again. ... Version 1 of this design should allow for effortless filament changes without having to remove the cover itself, and I also removed the cable bracket.

The runout sensor holder is tailored to accommodate the newer, smaller type of filament sensor found on the CR-10s. To ensure a proper fit, it's essential to remove all excess plastic from the sensor, creating a flat bottom surface. For mounting...

This bracket secures the filament sensor in place for the Creality CR-10S printer. It ensures precise alignment of the filament, thanks to its dual drive extruder design, which is slightly taller than the standard plastic version. Unlike other...

This modification allows users to securely attach their bond tech or dot bit on the original CR-10s bracket for the filament sensor, eliminating the need to print the oversized Bondtech bracket that originally came with it. To successfully implement...

The top cover is worn out, but i think im only one having this filament sensor with two screw holes

I had issues with my fully 3D printed hinged filament sensor, which consistently malfunctioned due to the filament bending slightly inside, causing the sensor to deactivate and interrupt the printing process abruptly. To overcome this challenge, I...

Revised: I moved the filament sensor to be more in line with the extruder and pushed it out to the edge, away from the Z chain. ... On the sensor's metal arm, you might need to bend it up slightly and cover it with tape, just like mentioned in...

... a little small and I couldn't tighten it enough to prevent it from slipping. ...Increased the size of the head so that it's easier to turn. Careful not to torque too hard - you can get a lot of torque and break apart the filament sensor's base piece.

Just design a filament sensor holder to put the original that comes from Creality in a better place if you are using a spool holder in the top of the machine. I need 5 iterations to get it perfect, but now I'm very satisfied. ...You can put the...

I've designed a filament sensor holder that relocates the Creality original component to a more convenient spot when using a spool holder on top. It's perfect for those who want a better setup. I've gone through five iterations, and now I'm...

Tried out the stock filament sensor adapter from arod24, but it didn't work with my CR-10S's extruder. Instead, I modified the design in Tinkercad by cutting away unnecessary parts. ...Big thanks go to all the talented designers who made this possible.

I edited it to fit with the filament sensor that comes with the Creality CR-10S. I made some improvements on the hole sizes and the part where you screw it into place, making it a bit bigger to prevent breaking of the small parts. The original...

Since upgrading my CR-10s to Direct Drive I've not been able to find a good mount for the Filament runout sensor that I liked. So I made one. This is designed to be mounted to the printer frame using standard M5 t-slot bolts (I had some leftover...

... ... This guide allows the use of standard 4mm push in connectors with a teflon tube to guide the filament into the sensor sensor. It will snap onto the filament sensor housing. ...You can use it with the spool on top or with a heat box on the side.

For direct drive, Moves sensor to the top rail. ...Mount in center and put your filament roll close to it as possible.

As kilometers of filament pass through this sensor, I utilized PTFE tube to minimize wear on the housing and ensure longevity. Additionally, several similar housings are available online, but they often failed to consistently depress the sensor...

The first version features a hole for the hose fitting, allowing you to feed the filament directly into the sensor through a tube. In the second version, an additional guide prevents the filament from coming into contact with the z-axis rod. The...

When moving the spool holder up, I opted for a straightforward push fit filament sensor holder. To achieve this, I utilized an old bearing as a makeshift guide and simply secured it in place using an M3 bolt. ...The main holder itself required...

I also thickened this section and increased the gap between the rod cut-out and the mounting holes 3) False triggering Some of my filaments false trigger the filament runout sensor whilst others do not - I believe it's down to the tolerance of the...

For direct drive setup, Mounts on top rail. ...Put spool holder close to the sensor

This is a straightforward adapter block for connecting a modified stock CR-10S filament sensor to the 3DFused X-Axis linear rail bracket if you've already installed it. Instructions: (1) Modify the stock sensor casing by cutting off the unnecessary...

CR-10S Hinged Filament Sensor Mount (Front Plug) https://www.thingiverse.com/thing:2791872 CR-10S Hinged Filament Sensor Mount (Bottom Plug) https://www.thingiverse.com/thing:2826099 Let's be honest, the filament runout sensor is a fantastic...

CR-10S Hinged Filament Sensor Mount (Front Plug) https://www.thingiverse.com/thing:2791872 CR-10S Hinged Filament Sensor Mount (Bottom Plug) https://www.thingiverse.com/thing:2826099 To be honest, the filament runout sensor is a fantastic addition...

this was a combination of an existing cr10s filament sensor mount (cant find original design) and a mount for 10x10 cable chain for the bondtech ddx direct drive extruder. ... Lever for switch mist be rounded at the end, to allow filament changes when...

To ensure a stable fit, I carefully drilled three precise holes for the screws and made strategic adjustments to maintain the sensor's optimal position. ...Double-check that the sensor's directional orientation is accurately aligned before proceeding...

The Creality CR-10s comes equipped with its original version 2.0 filament sensor, which is designed to monitor the 3D printer's plastic supply accurately, ensuring seamless operation without interruption.

Another option for the original filament runout sensor case from the Creality CR-10s printer. Attaches to a standard extruder location using four M3 nuts. ...The case is secured with four M3 screws.