cr 10s pro 3d models
88440 3d models found related to cr 10s pro.thingiverse
Uploaded this to help others design accessories for the CR-10S PRO hot end
thingiverse
Lightspo for CR-10S Pro LED Spot: Pollin LED Modul 32x32mm 12V https://www.pollin.de/p/led-modul-ip65-12-v-warmweiss-120763
thingiverse
Zusätzlich benötigt: 2 Zylinderschrauben M3 x 20 1 Kugellager 626 ZZ (d = 6 mm, D = 19 mm) - Filamentguide for Creality CR-10S Pro, it's screwed to the filament sensor. ... Additionally needed: cylinder head screw M3 x 20 1 bearing 626 ZZ (d = 6...
thingiverse
Hi everyone, When printing ABS i noticed that the Nozzlefan is blowing air on the bed. ...This Airblocker comes in 2 variants. One with the hole and one without. The Airblocker is compatible with the CR-10S Pro.
thingiverse
Hello Everyone, This is an alternative filament cooling fan duct for Creality CR-10S Pro. It will fit perfectly on the stock carriage of the hot end ... This fan duct should provide better air distribution around the nozzle ... You can use this fan...
cults3d
Fan duct for CR-10S PRO. Goes in place of the original one. ... Fixation by the 3 screws of the fan
thingiverse
Filament guide for the CR-10S Pro. ...Without this guide my filament was being shaved, and squeaked very loudly with every retraction.
thingiverse
A simple tool holder for the CR-10S PRO (all Allen keys, scraper, snips, spanners, nozzle cleaner, screwdriver, 0.2mm shim) Requires 2x nuts + screws
thingiverse
... de la cr-10S Pro ce petit support se monte facilement et ne nécessite aucun élément additionnel. ... Afin d'éviter une usure rapide des câbles de la tête de la cr-10S Pro ce petit support se monte facilement et ne nécessite aucun élément additionnel.
thingiverse
Filament guide for CR-10S pro printer. I designed this guide for pulling filament directly from dry box. 16/5mm bearing 5mm bolt and few 5mm washers needed for wheel. ... I used tree support in Cura for removing supports easy.
thingiverse
Simple part to make it easier to see on the CR-10s Pro when the extruder is moving, I used a small amount of superglue to attach to the extruder gear.
thingiverse
I cut the cap a tiny bit off to make the cap fit on my 2021 CR-10s Pro. The cap from adamdms did not fit. I recommend printing the cap from ABS. ... I used the ABS from Redline Filament.
thingiverse
This is a side exhaust for the CR-10s Pro. This can be used to vent hot air from the control box through an enclosure wall. ... 6mm magnets hold it in place.
thingiverse
... available from Thingiverse here: https://www.thingiverse.com/thing:3050607. My Cura settings (0.1mm layer thickness, temperatures, etc.) can be found by Curaprofile in the download files and is was printed with above mentioned Creality CR-10S Pro.
thingiverse
Extruder Mount CR-10S Pro Please consider donating a pizza or a spool of filament. ... <a href="https://www.buymeacoffee.com/RaptorHunter" target="_blank"><img src="https://cdn.buymeacoffee.com/buttons/default-white.png" alt="Buy Me A Coffee"...
thingiverse
Created this Combo Bracket for the CR-10S Pro as i liked both of these things listed below but could only install one as they mounting point was common. I combined the 2 here so that anyone else wanting to use these two mods can do so. ... ...
thingiverse
... ... I tried to use the original fan duct but the screw holes broke off. Therefore i reinforced them in this design. Take a look at my other [CR 10S Pro upgrades.](https://github.com/CaptainDario/3DPrinting)
thingiverse
simple filament guide for the CR-10S pro, using 6mm Bowden tube Update 11/26/2018: Updated the design so you don't have to take it off if you need to remove the sensor (which I've had to do a few times)
thingiverse
This is a 3d model of the cr-10s pro fan cover. I needed it for a project and saw that no one has uploaded any model of this so I decided to do it myself. If you want a STEP file ir any other format, let me know. I will gladly provide you with it.
thingiverse
This is a webcam mount I made for the CR-10S Pro for my logitech c270. It just snaps on the stepper cover for the x axis ( you have to unplug the x axis sensor to feed the wire through the hole). ...There is also a hole for camera that uses a tripod...
thingiverse
Z-axis webcam mount for Creality CR-10s Pro. Includes a couple of different mounting options. ... Hardware used: 1x M4x16 screw + 1x M4 nut + 2x M4 washers (attach mount to printer) 1x M6x35 screw (connect arm to mount) 1x 1/4"x3/8" screw (attach...
thingiverse
Hello, I am creating my box for my fdm Creality CR-10S PRO printer. I needed the approximate dimensions, so I created this model, because I can't find an official model. The model is in a sketchup file. ... Deepl translation: English > French > English
thingiverse
This is a remix from a good purge bucket, but made for CR-10S Pro, the is enough space for the nozzle. The arm takes less space ( can easily fit inside an existing enclosure ). Easier to mount. I use a baking ( pink ... ) silicone. ...
thingiverse
So I have designed the mount which mounts in the stock CR-10S PRO fan mount locations and uses the Petsfang cr10tevo_5015_duct_V7.5 found here https://www.thingiverse.com/download:5272122 I have included files for both the stock sensor (ABL) and a...
thingiverse
Unfortunately, the Creality CR-10S Pro has no integrated lighting for the heating bed, so I designed myself one. The sticky LED strip I had left of another project, based on 12V DC and is 3mm thick. Since the Creality CR-10S Pro is built entirely on...
thingiverse
Bonjour, voici une amélioration de confort pour la CR-10S PRO Fini le bruit de la turbine qui refroidi la CM Cette platine pour fixer 2 ventilateurs 40x40mm prend place sur la carte mère grâce à 4 entretoises nylon 16mm-M3 et les vis d origine. Si...