cr10 filament guide 3d models

Got a CR10 Max the other day, and noticed that the filament shreds a bit as it runs into the filament sensor. I used a Fidgit Spinner bearing, since they are plentiful. It takes a bit of pressure to get the bearing on, but apply evenly.To avoid wear,...

This filament guide works for all CR 10 varients, Ender 3, and Ender 3 Pro. The guide allows space for a stock Creality filament runout sensor. ...Non-3D printed parts include a PC4-M6 coupler and standard ender 3 Boden tube.

Vertical Spool Mount & Filament Guide for Creality CR-10v3 Remixed from a couple other models i found on thingiverse, print will be holding a 1KG filament roll so will need to be fairly strong. re-use bolts from factory spool mount to attach, I...

Didn't like the angle the filament went from the spool into the sensor. ...It did rub quite a bit there.

I'm designing an innovative top-mounted roll holder and feeder-guide that travels alongside the extruder. To assemble the small plate in the feeder STL, a quick-drying glue is applied for just three seconds to secure it into place. A...

Accessories for CREALITY CR10 This is a filament guide to attach to the top porticle of your printer for 6 filaments at the same time.

To load or unload the filament guide, simply slide the filament through the slot in the guide hole of the guide itself. This approach allows you to easily place or remove the filament guide without having to disconnect the filament. The goal is to...

you slide the filament through the slot in the guide hole in the guide guide. this way you can place or remove the filament guide without removing the filament. the idea is to keep the filament centered tand to keep it from going over the sides. this...

i made this to guide the filament into the extruder smoothly and accurately. no supports. i included a ready to print file as i think it should be. ... Category: 3D Printer Accessories

I designed this tool to guide the filament directly into the extruder with precision and ease. ... No supports were added, but I did include a pre-printed file, assuming that's how it should be.

The base is simply (loosely) clamped onto the filament runout sensor and the arm perfectly guides the filament straight into the sensor. __It can be mounted (or unounted) any time, even during a print__, because the hole at the end of the arm has a...

A small guide of filament without fixation wraps itself around a well-positioned spool holder, the spool holder not too far from the Z-axis at about 1 cm.

This filament guide travels together with the Z axle, ensuring that both the filament sensor and extruder work in perfect harmony. They witness the same consistent force pulling the filament along 400mm of Z travel during every print process. You'll...

This is a mounting for a pneumatic mount that sits before the extruder. ...I use this to have a bowden tube between filament dryer and extruder. ... Fits on the X-roller wheel assembly.

... stress points on the part You need one bracket and one bearing runner printed. ...Print Settings Printer Brand: Creality Printer: CR-10 Rafts: No Supports: Yes Resolution: 200 Infill: 50 Filament: Inland PLA or PETG Any Category: 3D Printer Parts

Additional you will need the following: 1x M8-1.25 x 1.25in or longer screw/bolt 1x M8-1.25 Hex Nut 4 to 8 M8 washers Print Settings Printer Brand: Creality Printer: CR-10S Rafts: No Supports: Yes Resolution: 200 Infill: 50 Filament: Inland PLA or...

For Direct Drive setups on CR10, a convenient clip-on filament guide makes quick work of integrating a Bowden tube into the system, ensuring smooth filament feed even during long travel moves by providing a gentle hold on the tube, preventing it from...

So i made this and solve my problem There are 2 parts, the guide itself and the ring lock Ring lock is optional but recommended, and the ring lock is designed a little bit hard to insert but it will lock nicely once it's in place You have to jam or...

I use a small support underneath the overhanging lip of the filament guide, which I remove after the print is complete. Insert the limit switch into the cap and snap it securely onto the panel. I used this specific limit switch: ...

I design this filament guide as compact as possible to complement my other Sunlu S8 designs. It's perfect for use on other 3D printers with 2020 top rails, requiring only x2 M3 10mm screws and rail bolts. ...Happy printing!

This guide outlines the process for installing a filament guide on top of the CR10S Pro 3D printer. A press-fit design makes installation straightforward. To secure the guide, I utilized TPU material, but PLA can also be used by applying heat if...

To tackle both cable and filament, I remixed a guide by combining similar parts with some minor adjustments. The original design was well-crafted by DOYENC, who deserves credit for the neat layout. My initial print at 20% infill failed due to...

To ensure a smooth process for both cable and filament, I merged two versions together - one a direct copy-paste, the other modified with some minor tweaks. The original design was cleverly crafted by DOYENC, boasting a tight and efficient layout....

I'm using a CR10-S with the "Ender 3 Filament Roller Guide" and it's working perfectly, but I've got one problem - the filament sensor isn't cooperating. So, I decided to create this remix to fix the issue. It was designed quickly, but it works great...

I liked the way the bearing clipped on from this Ender 3 Filament Guide - https://www.thingiverse.com/thing:4163954, so i attached the clip to ljbeng's design for a ease of use. ...

This allows the filament to be gently guided into the extruder, as it moves up and down with the sensor. As a result, the guide functions perfectly at any height level. The necessary components for assembly are: - The two printed parts, print the...

After integrating these components, my filament guide is now securely attached to my printer, eliminating any previous concerns about its stability. The roller design from Thingiverse's 3342775 has been incorporated into this new design. ... Both...

Simple oneshot design. ...Helps the filament sensor travel from left to right, very useful when dealing with more than one spool of filament. ... Just add M3 screws to the sides and the sensor and you are ready to print.

Lock Secures Patio Umbrella in Place When Tilted Against Sunlight. This Lock Is Specifically Designed for 37mm Umbrella Poles and May Work with Sizes Between 36-38mm, Though This Has Not Been Fully Tested Yet. To Express Your Appreciation for This...

This is a modification of the https://www.thingiverse.com/thing:4678852 I also added filets to all the corners to decrease stress points on the part You need one bracket and one bearing runner printed. ...