cr10 smart 3d models
21315 3d models found related to cr10 smart.
cults3d
This is based on the Ender 2/3/5 part-cooling fan duct (also fits CR10) by xeVox. So go over there and check out their superb cooler. This project started somewhere else. The desire to shed some weight from moving parts on my 3d printer. The CR10...
thingiverse
To be honest, it doesn't work very well, the Housing of the CR10 V2 and V3 blocks half of the camera's view. And I can't move it further down. In addition, the blue reflective Plastic sits right in front of the LEDs of the endoscope so the...
thingiverse
This project is based on the Ender 2/3/5 part-cooling fan duct designed by xeVox, which also fits CR10 models. Check out their exceptional cooler at https://www.thingiverse.com/thing:2757244. The desire to reduce weight from moving parts on my 3D...
thingiverse
Lamp is an Octohue (https://github.com/entrippy/OctoPrint-OctoHue) enabled smart bulb receiving status of my CR-10 from Octoprint. ... I use Blue: Printer Connected Purple: Printing Red: Print Cancelled/Failed Green: Print finished A...
thingiverse
This is a (intended) TPU wire passthrough for the MatterHackers CR10 enclosure. It allows wires to easily be passed through on either side of the enclosure (left side is obviously the most straightforward side without having to extend the wires). ...
thingiverse
Here is a rewritten version of the text: I printed this design in PLA as a solution to printing issues on my CR10 without having to purchase multiple new components. The project was inspired by Thingiverse's 2544186, which was itself a remix. I...
thingiverse
My CR10 came with a filament sensor that pauses printing when the filament runs out. I wanted to mount the spool holder on top of the frame, which was easy, but then the filament ran vertically straight down to the filament sensor. This had a...
cults3d
Tired of struggling with your CR10's cumbersome control box? This mod is just what you need! Get rid of the control box once and for all by taking it off. Next, install all the electronics under the chassis, making sure to save all the original...
thingiverse
Creality CR10 S5 Stabilizing Kit Mounts Technically Universal mounts due to adjustable top mount! I designed these using 123Design. The base mount has a twist of 29.4 degrees and a hole for a 10mm threaded rod. It can be attached to the frame of...
thingiverse
Human: I couldn't find a suitable bed cable chain for the CR10 v2, so I designed one. The lug connects with the screws that hold the bed level sensor and slides over the plastic holder where the cable attaches at the bed end, providing a snug fit...
thingiverse
CR10 SPOOL HOLDER UPDATE 27 11 2018 Light as a feather! 2 23 NOV 2018 New parts - Shaft Reduced, Bolt, Washer, Cup and Ax 35.8/Ax 35.6 bearing housing Two versions of the Bearing Housing - AX 35.6 and AX 35.8. (inside diameter) Choose the best...
cults3d
(Dropped from 68 Decibel to 32!!!) Get rid of the clumsy control Box Make it Safe Printable on the CR10(s) print volume The guts easy accessible for tinkering without turning the machine over Use as much original component as possible If you do NOT...
cults3d
Comme pour beaucoup c'est un problème de laisser le contrôleur CR10-S dans le caisson car l'électronique n'aime pas la chaleur ! j'ai donc imaginé un système pour le laisser à l’intérieur du caisson sans qu'il ne chauffe ! Je le refroidi par en...
thingiverse
Beaucoup d'entre nous ont le problème de laisser le contrôleur CR10-S dans le caisson, car l'électronique n'aime pas la chaleur ! J'ai donc imaginé un système pour le laisser à l'intérieur du caisson sans qu'il ne chauffe. Je le refroidis par en...
thingiverse
I recently acquired my shiny new CR10 V3......... Although this is a nicely built unit with some before hand tinkering needed to get it up and running properly, there were a few things that brought a quick question mark (Puzzled look) to my...