craftsman table saw dust 3d models
145984 3d models found related to craftsman table saw dust.thingiverse
... on this one (https://www.thingiverse.com/thing:2767618) by https://www.thingiverse.com/wt808. ... It was modified for an 1 1/4" Vacuum connector and a wider shield 34mm vs. 30mm. This is specifically for Craftsman Table Saw Model 315.228310. ...
thingiverse
Fits the factory guard of vintage Sears Craftsman model 113 contractor-style 10" table saws such as the 113.298142, 113.298032, and 113.298240. Dust hose adapter fits 2.5" Shop-Vac style hoses. Use adhesive to attach the flange to the horizontal...
thingiverse
I printed this to replace my Craftsman Table Saw blade height adjustment and angle wheel.
thingiverse
Crank for a craftsman 137.228010 table saw. I made the crank handle hole a little undersized so it would have a good bite when you thread the handle in. ... This will work for either the elevation or angle crank and will fit a standard size socket for...
thingiverse
I was wanting to make a miter sled for my Craftsman Table Saw but realized how expensive the rails are so built designed my own. These are 200mm long and have 5 holes for #10 counter sink screws. I am using 4 total for my sled. Hope you...
thingiverse
This is a replacement handle I designed for my Craftsman table saw. My old one broke and I couldn't get it glued back together! Similar parts sell for somewhere between 15-35 bucks online. Also will work with an Ace branded 10" table saw. Scale...
thingiverse
Craftsman 10'' Table Saw (Model # 315218060) Gear Rack - Part # 0134010228 #88 https://www.searspartsdirect.com/model/319si7aknn-000247/craftsman-315218060-table-saw-parts
thingiverse
Replacement handwheel for Craftsman Table Saw, model 113.221620. The handwheels raise/lower the blade and tilt the blade. These fit over the D-shaft. These handwheels may work with any D-shaft with diameter of 3/8-inch. It fits over 5/8-inch of...
thingiverse
Dust collection funnel for a 30year old Craftsman Table Saw. I was using a flat plate, but it clogged up with dust often. ...We will see if this is an improvement.
thingiverse
I stopped using my table saw a little while ago because it makes too much dust in my garage. I looked online to buy something like this but couldn't find exactly what I wanted. I made this simple design in Tinkercad. ...The hole at the top is for my...
thingiverse
An adapter between a Craftsman 10" Table Saw CMXETAX69434502 and a ShopVac QSP hose with the nozzle removed. Customized version of https://www.thingiverse.com/thing:1246651 Created with Customizer!
thingiverse
Replacement Craftsman table saw stand leg end cap. Original broke (see black part in photo). Designed a replacement with more support than the original -- thicker around the sheet metal and taller. ... No supports needed.
thingiverse
The miter locks that come with the [Powertec Featherboard](https://www.amazon.com/gp/product/B084ZF7SWN/) are not compatible with an older Craftsman table saw that I had, so I designed and printed these so I could use those featherboards with my...
thingiverse
This is a replacement for the outer belt guard (part 824359) for a Craftsman 113 table saw (specifically for 113.299315, but may fit others). This part is a subassembly of part 824360 which is both halves of the guard. ... I have also included a...
thingiverse
Designed to as a replacement for the Craftsman 10" Table Saw Belt Guard Part #: 60252. I've included the Fusion 360 archive file. It's a parametric design and can be customized in many different ways. ...The Pulley Hole Diameter, Wall Thickness, Length,...
thingiverse
I bought the feather board from Harbor Freight but the rail guide was too wide to fit Craftsman table saw, so I made this to fit the rail width around 15.5mm, Once you tighten the knob the rail guide will expand and hold on to the table. ... Including a...
thingiverse
This is a simple replacement for a broken Crank Wheel on my Craftsman Table Saw. The saw uses two of these, one for blade depth and one for the blade angle. Both have a special keyed nut that slides onto the shaft. The size of the wheel is based...
thingiverse
Two table inserts for the Craftsman 113.243310 12 inch band saw. Didn't find anything that would work on my saw so drew these up using DesignSpark Mechanical. One is more or less zero clearance the other has a larger blade cutout. I printed with ABS...
thingiverse
... fillet on the surfaces that led to me printing with supports and then having to sanding it off. I'm not in love with how the surface finish turned out, but it lives under the table of the saw, in a basement, covered in dust, so choose your battles.
thingiverse
I have a Sears/Craftsman 9 Inch Table Saw and could not find a good file on here that worked. My table saw has a .500 (12.7mm) with the flat to round dimension measuring .400 (10.16mm). Handwheel body is 3.5" in Diameter. The handle knob is 2.5"...
thingiverse
Adapter for the Kobalt Table Saw to go from the standard port on the bottom to connect to 2" PVC fittings or 2.5" dust collection hose.
thingiverse
This a dust collector, guard, splitter for saws that were made before saws came with riving knives standard. The riving knife only works for square cuts as it is built in to the throat plate. I have been using a throat plate for years, and this is...
grabcad
Simple model that is helping me configure my garage, done in CATIA with a .stp file for other CAD
thingiverse
... smaller table saw uses a different track than the one I had before so I had to modify the bar. It fits the Craftsman 10-in Table Saw CMXETAX69434502 This is my first creation I have uploaded - comments welcome and appreciated. ... Happy Printing!
thingiverse
Dust collector adapter for makita table saw
thingiverse
Dewalt DWE7485 table saw dust collection dapter
thingiverse
Designed for this saw but should fit other Craftsman/Skilsaw table saws with the same type of mitre slot. Intentionally left short so that you can place washers underneath to raise the rail above the slot for gluing to the sled. Very little side to...
thingiverse
... size replica of the original. ...I recommend PLA or any easy to print plastic, since it's just going to be worn away eventually anyway. It replaces Craftsman part number 69156 table insert, and fits band saw models 113244510, 113244512, 113244513.
thingiverse
This is a CRAFTSMAN 10-in 15-Amp Table Saw sawdust exhaust adapter for the 3 gallon shopvac. After downloading several which said their measurements were correct, I found none of them would work. I took measurements and gave the design over to Robert...