crash 3d model

I built the flat surface of the skirt with ParametricPlot3D, then intersected it with a lattice-like model, then I utilized those tables to make two ParametricPlot3D tubular surfaces, which I then pieced together using the Show command to make the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_mirror = 0 stencil_drawing =...

I have since printed out another model in ABS which I am hoping will be more durable. PETG would be another more durable substrate to consider using. Special thanks to Jim Harmon at Keystone College and Emmitt Zugar at Salem Community College for...

I hope this piece works for you; it was actually the most challenging to model and get right. 9. You should be good to reassemble now! 10. Put the hammer-trigger-piston assembly back in. 11. Lay the cylinder back in place, including the U-clip for...

unless you have a special edition like a Porsche, Mercedes, or older Audi, VW, or BMW model, which is what I have. For most of these special editions, the original push bar won't fit. I found a design on Thingiverse called *Klein-laui* and tested...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_top_port_corner_resolution = 8 custom_back_camera_x_position = 0...

Here is a 1:1 scale model of the first rover called Sojourner =) The frame is assembled from a 20x20 mm structural aluminum profile. All parts are printed with PLA plastic, everything fits on a standard 200x200 mm table, but it is advisable to use...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

(Well, two pieces since there are two jigs in a set.) The "wave" shape of the new version leaves more space for two layers of fabric and just works better. Print instructionsRecommended print settings, optimized for speed without sacrificing much...

You will, however, need to modify the hole in the motor arm to fit your motor's shaft, after you have scaled the model. You may also need to do some modification to the connector arms so that they clip nicely to the connecting rod that you plan to...

i may add a second hole for wiring so it doesn't have to be drilled by others but right now thats how i got the led to the inside under the boot an up through the hole i drilled, put the body on first b4 trying to run the wires or they will try to...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_x_position = 20 custom_back_camera_corner_resolution = 8 custom_bottom_fillet_resolution = 8 stencil_horizontal_position = 50...

Not a problem with a well-tuned MK3S+.    The box was printed usingFilament                                              ...

... mount and two each side for accessory mounts. I used one on the right for strain relief for E3D wires, 2 on left for fan mount. 4 on side fan, only two are used depending on fan model. ...2 on cable chain attachment to attach it to extruder mount.

That link also calls for using alanho's file to hold the TFT50, here is a direct link to his page as well: https://github.com/VoronDesign/VoronUsers/tree/master/printer_mods/alanho/BTT_PITFT50_v2_Mount I also made some simple changes such that it...

... some of the pictures may show older versions. All designs were made in (free) Tinkercad. You should be able to find each model there, if you want to tinker one. ...https://www.tinkercad.com/dashboard?type=tinkercad&collection=projects&id=dYW5jbPYAIP

For your Rubik's cube to keep the fluidity of its movements, it is necessary that the dimensions of the model are reproduced very precisely, and that your board can allow a first layer of 0.1 mm... Usually to deal with defects in the horizontality...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 40 printer_tolerance = 0.4...

It started with a Bachmann starter set with a steam loco and a couple of cars (Durango & Silverton in case my other models didn't give it away). This came with a bunch of EZ-track. I had full intention of expanding my layout so I bought more...

A hard case for your Eggtracker Mini to use with high power model rockets. Bill of materials: Eggtracker Mini (only tested with rev C3) Turnigy Nano-Tech Plus 300mAh 2s 70C Lipo Pack (hobbyking, amazon, search around and try not to get raped...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: phone_model = 0 custom_top_inner_edge_chamfer_radius = .6 custom_top_port_corner_radius = 5 custom_back_extra_port_corner_radius = 5...

We successfully engineered an incredibly stable and secure mounting arrangement by adjusting the RC roof rack's structural reinforcement through computer-aided engineering models. By applying advanced design methodologies, our innovative product not...

I have printed the model in 2 colors with an extruder, changing the color of the filament in Z: 150, except in parts 1,2 and 3 that have part of the roof and I have changed it in Z: 150.02. The dial I have changed the color of the numbers. I bought...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

(The toothbrush still shouldn't fall out, but a hole any larger and it might...)(I also use a print of the original model as a holder for fine detail paintbrushes, so a hole in the bottom of that one would be rather pointless.)Enjoy!Print...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

In many channels for the promotion of new electric bikes, people who access the channels, like me, are also excited about the new models of electric bikes, almost always great projects. However, many were frustrated because they would like to have...

A .3mf file and pre-sliced .bgcode file is available along with the STL models. Also prints well on a Bambu Lab P1S.Assembly/MountingThe inner fixture can be held upside-down to desired mounting position for marking the mounting holes. I found it...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_back_camera_x_position = 0 custom_top_port_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 48...