creality 3v2 3d models

Customized version of https://www.thingiverse.com/thing:1571860 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1571860

This is a remix of another filament holder. This is made shorter to accommodate Ender 5 Plus bed. Since the filament holder faces the bed, I edited the Ender 3 holder from https://www.thingiverse.com/thing:3209211, by...

porta led o neopixel per ender 3 pro o 3 v3

I changed my printer to Direct Drive from microswiss. Unfortunately, the direct drive is not compatible with the original hotend. So i adapted my own creation to the backplate of microswiss. ... Have fun!

X-axis endstop relocation kit for linear rails. ...Loses no x-axis movement.

This is a small 130mm tall jig you can use to align the left and right side of your print head carriage when you use dual Z axis steppers. ...It slots into the bottom of the frame and makes aligning the axis a breeze.After powering off the printer the...

STL`s are big becouse are in high quality! For fix You need 2 pcs 608 bearing and orginal screw for filament holder everything fit smooth on my printer if You get problems with screw change size in Y and X 2% less or more Inspiration i took from...

Remixed for the Pi3 and 40x40x10 fan. I just did a hack job on TinkerCad which works well for my use. I left the 4040 fan open so you can slide it up or down depending on heat sink. I thought I would have clearance issues but it was fine. I've...

This is a filament guide for the Ender 3 V2 with the upgrades First Layer dual gear extruder. The other models I found were not tall enough and did not left the filament spool freely. Also, it has a cable hook since this extruder takes that away.

quite simple, so that you can see better in the dark where you have to insert the sd card. I printed it with glow in the dark, but it's too flat for that. ...It is best to print in a light color and cut out double-sided tape

Tis is a simple clip to hold the ZXE cable to the frame, a little bit off cable management, simple and efective.

<p>Could not find one that i like and fit.</p><p>Cover with and without Voron logo.</p>

Another remix of the Satsana V52 with a direct drive bracket I designed. This one that I designed shortened the bowden tube length by 8mm. My previous setup was https://www.thingiverse.com/thing:4662728 The Satsana fan duct is remixed to be used...

Customized version of https://www.thingiverse.com/thing:1169605 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1169605

I remixed this design with an extra height of about 4m to give the Notcua 80x25mm fan better fitting room. ...I also removed the buck converter mount because it is not needed with the Noctua fan.

This is a remake of thing:4594025. It includes slots to see the time on the Ender 3 v2 Screen. ...Thanks to the Original Designer for the design

this work in progress is a mix of https://www.thingiverse.com/thing:4559133 and https://www.thingiverse.com/thing:4545252 as I have the bl-touch original plate installed so I had to adapt the pen holder

This pen holder is designed for general hexagonal ballpoint pen. The pen is mounted on the ender 3 v2 extruder gantry using m3 threaded hole for touch sensor. ...The pen also can be easily removed and attach to the mounting with m3 bolts.Blog:...

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

Reduce +/- 0,20 Horizontal Compensation (VERY IMPORTAN)

I have designed this tool myself since others don't work as well or at all. The works gagantiert ! No more filament breaks ! Clean konstrucktion ! ... Only 4 grams !

spacer made for the stepper motor and the aluminum profile, for a correct align between the thread from the z motor and the aluminum profile.

just print as is with your best print settings

If - like me - you have a bunch of different print nozzles in different sizes and materials, you're probably already tired - like me - of having a zillion little plastic nozzles bags generally being being in the way. So I made an organiser tray...

Original design worked as it should. Didn't like how mall the pick up knob was so i added a knurled knob. It is a bit taller and more tactile to the fingers. ...No other changes were made to size of cover, fits the screen tight and lets very little to...

This is the second version of my Ender 3 v2 Neo direct drive mod, in this version the idea was to improve the way the PTFE tube was placed and the space that the mod require, in v1 the mod used to interfere with the printer itself, this time, it...

End-clip requires 101% scale.

customized with 3D Slash!

this is a camera mount for the tapo 210/200 + you will need to print the base wich was made by https://www.thingiverse.com/isaknybo/designs

The original stepper-mount for the z-axis is not well made as incection molded part. The angle of the stepper-axis is not vertical. ...So I replaced the original part with this copy.