creality 3v2 3d models

This is my small project. I very like Voron extrude but I wanted a more compact fan duct so I redrawn it Use M3x10 screws to connect the parts. ... No support needed when printing

I combined 2 models to create this extruder knob topper for the ender 3 v2 https://www.thingiverse.com/thing:4736138 Ender-3 v2 Extruder Knob Overlay by edk_sc January 24, 2021 https://www.thingiverse.com/thing:2033990 stackable fallout...

Simple print-head design that uses the original two anchor screws to the gantry adapter plate, rather than the heat-break screws. ... Designed to fit by friction or screws, either side wedded to and supported by the main cooling fan, and to fit a 5015...

Remixed version of the RODAM Ender 3 spool holder, which was made by Rodamyot. ... This version can handle some larger spools.

Y-tensioner (for ender 3, V2,PRO) modified for installation of a direct drive (see my YT chain with direct drive links). ... Modified by SIX SAUER ;-)

<p>Scaled down the knife to fit a ender 3 v2's print bed.</p> Category: Other

A holster for a Magigoo pen or a glue stick for the Ender3v2. It's perfectly sized for the Magigoo pen but you can also throw in a gluestick in there if that's what you prefer. The benefit of this design is that it's not in the way of any of the...

It's a small remix to fit the weather vane onto the z axis. Done in tinkercad, as a learning experience. Printed without supports and infill 0.24 mm layer height. The model was glued together and sprayed with gold spray paint. ... It looks...

it connects to the non stepper end of the x axis bar, unscrew the tensioner then slide the model on the, screw the tensioner back on and then slide the camera in. ...make sure to print with support, i tried many different models but none suited my...

original BL touch was mounted in a way that blocks the mounting to x carriage mount is from thingiverse making it difficult to adjust too toolhead i am also using cr touch mount comes from satana before using voron i was using this mount. ...thanks...

I had a magnetic catch bowl for holding screws, and I wanted to mount it to the printer, so I designed this little platform that takes a big washer that I got at Home Depot for less than 50 cents. ... Washer Outer Diameter: 50mm Washer Inner...

I made this holder for Ikea Mittled (40cm) led light 24v. I design it for M4x20 screw, mounted on top of printer with t-nut. It's slide from side to light frame. Printed on side. I made it with switch next to the screen. ... Hope some one will need...

Housing for 5' Capacitive Touch Display with DSI Interface. Will fit Ender 3 V2, Pro and clones. ... https://www.waveshare.com/product/5inch-dsi-lcd.htm https://klipperscreen.readthedocs.io/en/latest/ Other hardware: M3x10 Socket head...

Made room for the spider hotend as it is wider than stock. Also extended fan ducts to match the nozzle. These are my values using cr-touch mounted with extra m3 bolts under the mount to reach under nozzle. Using mount from original project. ... ...

THIS HAS NOT BEEN TESTED so basically I'm doing a bottom feed for my printer and this is the first part. this will allow the filament to come straight up into the extruder. ...Bowden tube will be pointing straight up

I was looking for mount for this cable chains, bcs I didnt found any, I made my own.

I bought a double Z motor and the old design didn't fit. So I remake it. ... You can attach it to the top or side of the 3D printer

Install a direct drive and need a new filament guide that stays out of your way and keeps the filament from getting in the way? Then this is the filament guide for you. It uses the top 2020 rail of the Ender to clip on a guide that pivots as the...

Max Verstappen Lion logo extruder knob

The ender 3 V2 hot end assembly attaches with one screw in the back, instead of two in the front on the ender 3 and ender 3 pro. ...I made a small change in this part to go around the screw on the ender 3 V2.

It is an end switch cover for Ender 3 V2 but it would fit on others with hight of cover 42mm. ... I took dmaccalums awesome design (thank you) and scaled it down and added a bracket.

Another tool holder. Added some extra holes for scissors and nozzle cleaners ect. Added front container for holding screws and crap you don't want to lose when fixing your latest effing printer issue or upgrading something that completely does not...

Could not find a mount for the Creality Runout Sensor for my Ender 3v2 printer with the Creality Sprite Extruder Pro Kit. The sensor only came with a mount for the original Bowden setup. So, this is what I came up with. I used M3x4x5 Threaded inserts...

PT: Você preza pela organização no ambiente de trabalho? Então não quer deixar as ferramentas da sua impressora desorganizadas, espalhadas pela mesa ou até mesmo penduradas na impressora, local que receber vibrações e pode causar ruídos...

imprimer a horisontale &non verticale

Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069

<p>Its the print testfile that comes with the ender 7</p><p>&nbsp;</p><p>Fuzzy skin:<br>0,4 distance<br>0,3 thickness</p>

Its just a random knob I wanted so I figure why not put it up here!

Following a small accident where I sprayed the logo of my 3D Printer with acetone, it was partially erased. Also, I decided to print another one to stick on instead of the paint. I used the Fredo Corner plugin in sketchup to round off the angles. I...

Simple Keychain