creality cr 10 filament guide 3d models

Combined these to filament guides into one for the CR-10 V2 https://www.thingiverse.com/thing:4683505 https://www.thingiverse.com/thing:4023754 I liked the big roller from Markacho's design and wanted that for my CR-10 V2, so I used gmuddy's mount...

Here is a rewritten version of the original text: Long-term users swear by CR-10 and Ender 3 printers for their smooth filament feeding and precision extrusion capabilities. A well-crafted guide is essential for optimizing these systems to produce...

I'm working on a project at school that involves creating a filament guide for our CR-10 printers, allowing us to mount the filament on top of the printer. The design also works seamlessly with the Ender 3 model; if you have any ideas or encounter...

... ... The CR-10 V2 has limited top-mounted filament guides, so I came up with this one. Initially, I had to scrape out the mount for the spool, as the slot proved to be a stubborn bridge to print cleanly. ...Nevertheless, it's now complete and sturdy!

I've secured my filament spool to the top rail of my CR-10, and I required a straightforward solution to prevent it from unraveling all over as it unwound. I designed this simple guide to keep things under control, and it performs exceptionally well...

To address this issue, I wanted to incorporate a filament filter that doesn't rely on hinges or lids and can be easily oiled while the printer is running, eliminating the need for downtime when using a stock CR-10 hot end. Currently, I'm searching...

I was looking at several of the filament guide rollers people have designed for the Ender 3 and the CR-10. I decided to make my own version, specifically one that allows the bearing and V roller to rotate a bit. My filament reel is up on the top beam...

This is a Filament guide for the CR-V3 which goes on top of the filament sensor. It helps aligning the filament into the sensor, as the sensor has sharp corners where the filament can scratch and create particles. Would recommend using PETG as...

This is a Filament guide for the CR-V3 which goes on top of the filament sensor. It helps aligning the filament into the sensor, as the sensor has sharp corners where the filament can scratch and create particles. Would recommend using PETG as there...

These parts are assembled to form a filament guide specifically designed for the CR-10 with a direct drive extruder. I opt for the direct drive kits available at https://printermods.com, a upgrade that I highly appreciate over a Boden. However, I'm...

A cable guide for my Creality CR-10

A cable guide for my Creality CR-10

The initial Filament Sensor-Box caused us numerous issues; however, we found an improved version that surpasses the original by Creality. ...The accompanying photo-manual provides essential mounting details and showcases the enhanced features of the...

I downloaded and use the TUSH spool holder for my CR-10 control box, noticing that the filament rubbed against the edge of the box and was beginning to scrape away the paint. I quickly threw together a solution and it works surprisingly well. ...Whether...

Found that when I was printing with PETG on my CR-10 V3 it was rubbing on the filament sensor. I believe this was causing slight under extrusion and forcing the extruder to have to pull filament with added resistance. I found bmonnin's design and...

To support filament mounted at the top of the CR-10 / Afinibot A31, I will remix this contraption. After making some adjustments, the bend in the filament is minimized to reduce noise levels. Additionally, the interior space has been expanded for...

... in conjunction with an Upper-Positioned Spool? ...Want low friction and straightforward filament swapping while utilizing the enhanced filament sensor on your CR10? ...Our model offers a solution, accompanied by a detailed photo manual for guidance.

Filament detector guide 1 Limit sensor 3 cm of PTFE one M3 screw of 10 to 15 mm, not more! insertion of PTFE to make the markings of the cuts (possible to heat "a little" to facilitate its insertion) and remove it to finish the cut and clean if...

In the upper bracket we install roller and guide so bar doesn't jump off roller. We assemble stand, put necessary number of bearings on axle, I put three, snap it in. ...Put on coil, tighten, I remind, thread is reversed, so coil doesn't unwind clamping...

This is a basic filament guide that ensures the controller box remains at an optimal position, preventing the filament from rubbing against the spool rim.\r\n\r\nAttached securely to the box using dual adhesive strips.

... with the angled bracket. Hardware required: 2 x M4 screws 2 x T slot nuts original model used for the spool holder: https://www.thingiverse.com/thing:2641586 original model used for the filament guide: https://www.thingiverse.com/thing:3059604

Their design's form factor caught my attention, but I noticed that the original filament guide was tailored for the stock printer height. Since the Winsinn intake is positioned 17.5mm away from its mount, I decided to modify it using Tinkercad to...

Filaments are guided effortlessly onto the sensor of CR10 S printers using a specially designed filament guide featuring either a printed or a sturdy 608 bearing sheave. This innovative setup eliminates the need for any screws, making it incredibly...

I used this filament guide for the ender 3 to make a guide without taking anything apart on the printer to install it : https://www.thingiverse.com/thing:3052488 You will need to print: 1 - bracket 1 - ring 2 - spacers Plus you will need: 1 - 608...

I used this filament guide for the ender 3 to make a guide without taking anything apart on the printer to install it : https://www.thingiverse.com/thing:3052488 You will need to print: 1 - bracket 1 - ring 2 - spacers Plus you will need: 1 - 608...

Replaced my stock extruder with direct drive and doesn't want to relocate my filament runout sensor. Hence I remix this to be able to guide it before and after the sensors. ... The PTFE tube should be tight fit, but depending on your tolerance / OD of...

I designed this filament guide because my past experiences showed me that others and I had to tighten the two screws holding the brass nut of the lead screw, which are meant to be loose, and by doing so, I also prevented the filament from touching...

I created this filament guide because with others I had to tighten the two screws holding the brass nut of the lead screw, which are suppose to be a bit loose, and this way I also prevent the filament from touching the lead screw and get lubricant on...

I designed a filament guide to use in conjunction with an air-tight storage solution, specifically the Ikea Samla 22l box, which will sit under my desk. ... I experienced issues with moisture in my filaments, so I decided to create this air-tight...

... this accessory specifically for pairing with my overhead spool holder system. ...Strategically designed cutouts in the tubing and bracket components enable users to easily thread filament through, even when the printer's spool is already loaded.