creality cr 10 y axis pulley 3d models

You'll need to replace your CR-10's (or CR-10S) existing cover to use it. A direct replacement for the OEM motor cover can be found at: https://www.thingiverse.com/thing:2866898. The camera is secured with a simple sliding clamp at the end of the...

Its purpose is to allow users to accurately measure their machine's axial movement, enabling them to precisely set steps/mm in the x, y or z axis. Required hardware consists of: An M3 nut A long M3 screw (over 10mm) - I used a thumb screw An M4...

Mounting the filament guide requires a clear path on the Z-axis. ...Simply attach it with the spare parts provided with your 3D printer.

NOTE LENGTH OF ALUMINUM TUBE HAS CHANGED COMPATIBLE WITH DUAL Z MOD I realize this is one of 10+ nearly identical mods at this point, but I was frustrated with the existing offerings because they required more hardware than I thought was necessary to...

K40 y-axis belt tensioner and pulley replacement Remove the gantry 693ZZ Bearings K40 Laser Cutter Alignment I ordered these metal pulleys complete with bearings but they arrived too late In the end it works fine, I think a toothed pulley would be...

Using this pulley allows for the substitution of a y-axis pulley with the bearing provided in the k8200 kit. Intended to be used with GT2 belts and 16 tooth pulleys, these bearings boast a tight clearance. Printing at a layer height of 0.2mm is...

The Y-axis Pulley for Prusa I3 GT2 Belt system requires precise calibration and synchronization to ensure smooth operation. The pulley's alignment is crucial, as misalignment can cause the belt to vibrate or even break, leading to costly repairs and...

... ...The pointer base is designed to honor YACC's profile, found at https://www.thingiverse.com/thing:2591854, acting as a similar cable clip. The purpose of these pointers is to simplify the detection of both Z-axis motors getting out of sync.

**You sacrifice some Z axis height** with this mod; however, I have not calculated the exact loss. Edit: Approximately 20mm. Perhaps I will develop another version where you lose none. **Furthermore, you will need:** 8x M4 tee nuts 8x M4x15mm...

[K40 y-axis belt tensioner and pulley replacement](https://www.thingiverse.com/thing:4344899) [Remove the gantry](https://www.youtube.com/watch?v=NKoJ3D0ZVSM) [693ZZ Bearings](https://www.amazon.ca/gp/product/B078SJKNBK/) [K40 Laser Cutter...

I was impressed by the simplicity of using a zip tie to stabilize the y-axis pulley on my Wanhao i3 duplicator, but I felt it was a bit too makeshift. So, I came up with this solution. The stabilizer glides over the existing front panel and then the...

Original Part ----------------- This is my take on a Y-axis linear rail conversion for the Creality CR-10 V2 and V3. It allows for mounting the bed plate to two parallel MGN12H linear rails with two blocks per rail. Unlike many designs, this does...

A cover is placed to prevent the T-shirt from getting stuck in the Y-axis pulley.

The Creality CR-10's hard Y stop can be fatal for its switch, ultimately causing it to self-destruct one day. A delicate clip has been custom-designed using OpenScad to significantly reduce the impact of this stop, making it much more forgiving.

Support Mount for GT2 Idler pulley. You need M4 T-Nut and M4 Bolt. ... "Touching Bed Support" needed.

This version can use the original Creality pulley, personally I use a threaded pulley with a 3mm hole that puts the belt right in the axis of its fixing to the bed, your call... For the fixation, an M4 screw of 10mm is sufficient with a T-Nut. To...

You will need several key components: Three #6-32 x 1 inch screws are required Three #6-32 nuts will be necessary A pulley that fits perfectly in the hole is a must-have Two screws to attach it to your printer (measure the hole size after printing,...

Simple and affordable to construct, a Z-axis frame brace for the Creality CR-10 features built-in fine adjustment, allowing precise setting of the geometry of the z-axis frame to exactly 90 degrees relative to the base frame on both sides. This setup...

When I finally got my CR-10 the Y endstop and mount had broken during shipping. I couldn't find the mount on here so I redrew it in Fusion and used 1 of my other printers to print it. Once the new switch arrived I had a working CR-10. Mount has been...

This bracket allows for straightforward use with or without motor dampeners, eliminating the need to adjust y-axis limit switches. Update 4/14/2018 - The STL file has been reuploaded with corrected scaling. ...To make the outdated version work, simply...

I propose the Remix of L-10 X Pulley Cover by clavenmoo, enabling those who desire to install this cover with the part used for Z chain below https://www.thingiverse.com/thing:2757810

You can utilize the original CR_10 Y belt tensioners screws or your own M3s, and a stiffening rib is incorporated for consistent grip on the idler. This results in improved overall performance. Due to the addition of screws, the back (screwhole...

Cache Courroie X (Belt Holder) for CR-10/CR-10S. ... Standard Unmodified Version Shared.

I just got my brand-new CR-10, but unfortunately, the Y endstop and mount were damaged during shipping. I couldn't locate a replacement part on the website, so I decided to create a new design using Fusion 360 and used one of my other printers to...

Support for raising the 125 mm wide main block of Creality CR 10 3D printers and derivatives.

When I finally got my CR-10 the Y endstop and mount had broken during shipping. I couldn't find the mount on here so I redrew it in Fusion and used 1 of my other printers to print it. Once the new switch arrived I had a working CR-10. Mount has been...

I'm grateful to donnyb99 for his outstanding y-axis belt tensioner. I had a hex head M5 screw missing and didn't want to make an extra trip to the store, so I decided to get creative. Using Tinkercad, I redesigned the knob and puller to accommodate a...

... and a vibration damper attached to the back of the motor. The assembly process doesn't demand long screws; standard screws suffice, such as M3 4 / 6 / 10 mm. Two pieces are needed to print. ...Infill should be set at 80%, with layers of 0.2 mm.

... (https://www.thingiverse.com/thing:2920581) and a vibration damper on the back of the motor. The assembly doesn't require long screws, standard screws are sufficient (M3 4 / 6 / 10 mm). 2 pieces to print. ...Set infill to 80%, layers of 0.2 mm.

This is an exclusive revamp of the X axis cover for the incredibly popular CR-10 printer.