creality ender 3v2 upgrades 3d models

This is made for attaching a button switch onto the ender 3v2 and use it with octolapse to take a picture everytime the nozzle goes on right back position You Need a Pc button switch like this:...

I was looking foor a SD card holder to fit on my Ender 3v2 but i dit not found something i liked. So i created something that should fit in the place where the end cap is. It fits perfectly in the four holes. ... 360°: ...

This is for microswiss direct drive on ender 3V2. Supports are needs for everything but the cable chain and chain covers. Printer mine at 10% infill. resolution doesnt matter. I printer 25 chain links and 50 chain link covers. Work with almost all...

I was looking foor a SD card holder to fit on my Ender 3v2 but i dit not found something i liked. So i created something that should fit in the place where the end cap is. ...It fits perfectly in the foor holes.

A holder for my 3D pen that will clip in the rail behind the screen on an Ender 3V2. The holder that came with the pen is useless and it falls over easily so it's a safety issue for me. ... It could do with some minor changes but to honest, it works...

This is bracket for "GoPro" style camera, to mount it to the bed of Ender 3v2. ... It allows to create nice timelapses, not as nice as Octolapse, but if you have some sports camera it is 0$ :) This is an example video made with Yi action camera and...

Like this one as it is very compact but as I have a MicroSwiss Direct-drive for the ender 3v2 I needed to modify for the mounting holes. This is almost the only fanduct where you can probe almost the whole bed. ... And I modified it to be printable...

shrunk the reservoir so it fits on a ender 3v2 but still works with the original bamboo, tap, and strut. the water brick has been combined with the reservoir. I have not printed this out yet. Will update when i get around to it. If anyone is...

This is a remix of "Voxelab Aquila Snap-on Bed Handle" that fits the ENDER 3v2. I used 4 walls and 40% infill for a sturdy handling. It has a really tight fit, be careful when assembling! ... Make sure your "Hole Horizontal Expansion" in your slicer...

Simple inlet vent for Ender 3V2 power supply cover. The factory fitted cover blocks the inlet vents for the power supply thus throttling air flow. These are two separate vent designs that will clip into a 28mm round hole drilled in the outer casing,...

A little tool holder that fits on both sides of the Ender 3/3 Pro/3v2 or similar printers. Remixed it, so it can go all along both sides and prints as one body(unlike the original that had two bodies in the model making the part less robust). ...

This combines a bed handle with the bed level knob locks. Bed Locks are labeled for easier install... LF = Left Front RF = Right Front LR = Left Rear RR = Right Rear Tested on Ender 3v2 but might work for Ender3/3Pro and possibly CR series. If you...

This is bracket for Ender 3v2 screen, to mount it on the left side, on the top of 40x40 profile. I couldn't find anything that i liked so I designed it by myself. It uses original screw and T-nuts. To route the ribbon cable to left side is very...

An extension block that fits over the front of the Ender 3V2 left-hand side aluminum extrusion, so there is no need to remove the bottom right screw as this screw is one that actually holds the PSU in place. This will enable you to add things like...

Simple bracket to mount the screen on an Ender 3v2 to the left side, using the existing hardware, and it clears all moving parts. ...Just unscrew the original bracket, use the screws and t-nuts to attach it to the other side, carefully pull the ribbon...

Remix removed text from face of the cover and worked on fitment/contour to match Ender 3v2. (MicroSD Cover with Angle - Full Panel.stl) Added a nice angle to allow for easy removal. (This one is my favorite). I added some extra support inside at...

Auto Power off Switch for Ender 3v2 made on a 3v2. Connect a Switch in row with the existing general switch on the back of the printer. For further information on how to open the case e.g. see this post: https://www.thingiverse.com/thing:4779435 ...

puts the Z motor about 0.20mm away to get the rod parallel mounting with original screws

puts the Z motor about 0.20mm away to get the rod parallel mounting with original screws

## **Requirements** * Standard mk8 extruder in bowden setup (as in a factory Ender 3v2) * **sensor-mount.stl**: * Filament being supplied from the side of the extruder * I use [The rocket](https://www.thingiverse.com/thing:4691695) side spool mount...

Angled bracket to fix filament spool holder on left side of ender 3v2. I remade original design, this one uses 2 original t-nuts and screws to fix from left side of the printer. You also need 2x M5 screw and 2x M5 nut. This bracket is a bit...

Ender 3V2 Direct drive cable guide placed where the extruder motor used to be 31mm by 31mm radius bolts for those that have Unitak DD configuration, and have modified other bits, I needed all the wires fed and held in a certain position so this ive...

... LF = Left Front RF = Right Front LR = Left Rear RR = Right Rear Tested on Ender 3v2 but might work for Ender3/3Pro and possibly CR series. If you only what the bed locks, you can print 2 sets of the Rear bed locks and use them as follows...

This mounts a small size dial indicator onto the Ender 3V2 hotend using the existing BLTouch mounting holes. The mount can be permanently attached without interfering with normal operation. The dial indicator provides a more accurate and easier...

Just another set of squashball feet for a Creality Ender v2. The feed slide over the existing feet. ... You can print 3 regular feet, and one slightly different which needs to fit next to the PSU cables.

It is an end switch cover for Creality Ender V2, but should fit on others with end switch cover hight 42mm. ...I took Dragon skull from Skyrim from dmaccallum (thank you) scaled it down to size and made a bracket.

Another Spool holder for Creality Ender 3 v2 inspired from https://www.thingiverse.com/thing:3523679 No bearing neaded: works well, my spool is well rotaoting without hard point PLA 20% infill 0.25 mm thick layer 6h + 2h50

As those of us with Ender 3v2 machines will find out, the stock cooling duct will slowly deform and melt causing us to replace it. Many of us have looked for replacements, upgrades and anything else useful to fix this. I have ran other common hot...

Here is a indicator-style boss added on to an Ender 3V2 extruder cover, enabling easy attachment of a Dial Indicator to the extruder housing. Also included is an STL file with a couple mounting brackets that allow mounting in different...

A BMG direct drive mount for Ender 3V2, designed to work with the Satsana fan duct (https://www.thingiverse.com/thing:4623647). The plastic bracket supplied with the BMG clone is used and attached with suitable screws (may need to drill and...