creality ender models

https://www.thingiverse.com/thing:4750218 - Trianglelab CR-10 (Ender 2, 3, etc) Easy Fit 40mm Cooling Duct. This is if you are using ALL METAL hotend like this one: https://www.aliexpress.com/item/32909386487.html?spm=a2g0s.9042311.0.0.6afe4c4dQbM199...

In the mean time there are many available here on Thingiverse that are fully compatible with the E3D Minimalist. Tinker with these here: https://www.tinkercad.com/things/lUsYFPTgxeZ Print Settings Printer Brand: Creality Printer: CR-10SRafts: No...

This is same model but I drilled 2 additional holes for easy screw access. ...

Just notched out the bracket a bit for the CR Touch cable to clearance. ...Original model works fine, but puts too much stress on the small wires.

Rough model, there are some small bits left from subtracting complex shape of the base part, but slicer ignores them so they are not a problem, prints just fine. Mount with two M3x6 screws to existing holes and a cable tie. ... It seems that I...

This model does not require supports if you print at low resolution and low speed. Its fixation to the printer frame is a bit wider than the original to enhance solidity. 2 bolts/T-nuts (the originals of the support) are on top, 1 additional...

BoQ: AC Power Socket with Switch and Fuse: http://got.by/3jt6h4 DC-DC 5V 5A Module, High-Quality (Synchronous, TPS40057): http://got.by/3jt510 DC-DC 5V 3A Module, Conventional (LM2596): http://got.by/3jt5qh Four M3 3X4mm Thread Brass Inserts:...

Bill of Quantities: * AC Power socket with switch and fuse: http://got.by/3jt6h4 * DC-DC 5V 5A module, high quality (synchronous, TPS40057): http://got.by/3jt510 * DC-DC 5V 3A module, conventional (LM2596): http://got.by/3jt5qh * Four M3 3X4mm...

If you'd rather use an ezable sensor, just stick with the original model linked above. I've also included a solidworks file for your convenience. To set up the firmware offsets, start by tweaking the X axis to +47, then adjust the Y axis to -2.4. ...The...

I remixed the model from Hesi-Re (https://www.thingiverse.com/thing:4095160). I have added a sliding to the cover. This way you do not have to screw the whole thing, but can easily slide it on. The case not only protects the LCD display, but also...

 Required: 35mm PTFE Tube (Goes between V6 and Extruder) M3 x 10mm Screws (8mm will also work)NotesBLTouch Coordinates :  X = 37 , Y = 6Printed with .6mm nozzle15% Infill on back mount, 10% in duct.2mm layer heightPETG or...

Here's a breakdown of the content: **Components:** * Opto-switches * Bolts and nuts in various sizes (M3, M4, M5) * Sliding nuts * T-nuts * Aluminum corners **Bolts and Nuts Sets:** * M3 bolts with hex head and nuts set of 340pcs * M4 bolts with hex...

Required hardware consists of: An M3 nut A long M3 screw (over 10mm) - I used a thumb screw An M4 drop-in tee nut A socket head cap screw with a 15mm diameter This tool is designed for use with a Mitutoyo caliper, but the STEP file has been included...

-added top cable grip to use with a plastic band *NOTICE*: there are two model types, one with an extra arc on the bottom and one without; choose the one you like; I personally prefer the first one; it may seem uncomfortable but helps level the bed...

UPDATES!:\n-added EZabl mount for right and left side; testing is impossible at present, if someone could kindly test the mount that would be great.\n-improved fit for blowers; they should work better now\n-added space bar between blowers\n\noffsets...

Calibration test-angle for 3D printersX, Y & Z written on the axis. //////////////////////////////////////////////////////////////////////////////////////////////Note that I recommend calibrating the extruder before proceeding with this...

Calibration test-cube for 3D printersX, Y & Z written on the axis. //////////////////////////////////////////////////////////////////////////////////////////////Note that I recommend calibrating the extruder before proceeding with this...

Suits 4 springs each, making a total of 16. You can get away with using only 3 springs per unit, for a total of 12. Perfect for OD sizes around 8mm in diameter, similar to the stock bed leveling springs or the cheapest ones you can find on eBay. To...

This small device helps protect the filament from contaminants such as dust.A piece of sponge, pre-lubricated with a small amount of alcohol, is inserted into the filter.Tighten the cable tie into the special recess located in the middle of the...

questo upgrate per la stampante permette di far scorrere con meno sforzo la bobinahttps://www.paypal.me/fabiopichini

This design allows users to access their tool tray without any limitations, providing them with complete freedom and flexibility in their workflow.

The stock bracket holding the 40mm fan inside the case is a subpar piece of acrylic that cools stepper motor drivers.\r\n\r\nTo solve this, I designed an alternative bracket allowing use of either a 4010 or a 4020 fan instead.\r\n\r\nYou'll need two...

<p>To mount the pen holder, screw it under the original part cooling fan.<br><br>Remixed from <a href="https://www.thingiverse.com/thing:4924000">this thing</a>, because I had Problems with the pen wobbling on the paper. ...This version does'nt include...

Customized version of https://www.thingiverse.com/thing:5946258 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5946258

The handy lift lever makes it a breeze to raise the z-axis swiftly.

Autolev Sensor Revolutionizes Auto Bed Leveling for 3D Printing! Your first layer just got a whole lot better! Introducing the Autolev sensor, a game-changing innovation that ensures your auto bed leveling is always spot on. ... Learn more about this...

I've been putting Prusa Slicer to good use lately, achieving impressive results. To give it an even more polished look, I decided to upgrade each of my printers with a custom build plate. This not only enhances the overall appearance but also makes...

Quick and easy to print clip that can be installed to avoid the vertical movement of the bowden tube during extrusion/retraction (the OEM coupling is not very good, so after a couple of months it started failing allowing the tube to slightly move). ... ...

I revamped this design based on nasty_ninja_bear's original concept, but I felt the clamp needed some serious reinforcement. To strengthen it, I made significant changes to its structure. ...Additionally, I added a slot for an M3 square nut and tweaked...

Here's a mount I designed to allow for easier marking of filament for E-Steps calibration. Background / why this was made - I have a lack of motor function (hand function), my left is worse than my right, so being able to hold the filament, a ruler...