creality filament sensor 3d models

A cover to protect the Creality CR6-SE Z sensor from bumps and dust.

Improves print quality, filament handling and enhances the stability of the cable hose.Remove back right corner coverReposition feed stepper motor as shown in the pickture Position filament feedPosition hose clamp Optional: move filament...

Ender 2 - Filament holder Extender https://youtu.be/mEyUU9S1J3Q The original width of Ender 2 Filament-holder is 80mm. I use Filament Spools with 94mm width, also. So i create an extender to upgrade the width. 1. Print the two sleeves. 2. Cut the...

The retraction of the filament is better supported this way, which prevents printing problems from occurring due to the media eventually coming off.

... you up to focus solely on loading the new filament. Once you've got the new filament in place, squeeze the extruder arms one more time and carefully remove this handy clip, allowing you to continue with your print without any further interruptions.

Filament guide for my ender 3 with the bondtech mounted on the backside. Uses standard 608 bearings and 4mm screw/nut. ...print your own spacer for the bearing.

This part bolts on to the top of a rod on the Z-axis Print 3 bearing casings Print 3 bearing pins Print 1 filament guide

I made this in Fusion 360 because I could not find any filament guide I liked. ...This has workped perfectly for me yet.

I designed this simple guide so my filament filter doesn't mess with threaded rod. ...I designed 3 versions with different gap position and 1 without any gap.

... caught my eye. ...The only thing missing was a compartment to insert a sponge piece and alcohol so it could clean the filament properly. ... The original STLs are: https://www.thingiverse.com/thing:2917932 https://www.thingiverse.com/thing:3176385

If you have relocated your filament spool to the top of your printer (check out my relocation bracket: https://www.thingiverse.com/thing:5809932 ) you may want to also add this remixed filament guide. ...Check out Holspeed's instructions for...

... with the printer. ...To add an extra layer of stability, I installed my spindle holder directly above the printer, which required some additional reinforcement. Simply place the filament on the spindle holder and then tighten it firmly with the nut.

Inspired by Greg191134's brilliant snap-on design, this revised guide eliminates friction between the filament and the spool when mounting it on top of the frame, like the Ender 3, thereby preventing problems that often arise. ...Instead, it cleverly...

this is a simple design to stop the filament roll from being able to jump off the filament holder. Designed by Jasper (https://www.3dprintitall.com) Like, Share and comment: https://www.instagram.com/3Dprintitall/...

Ender 3 Pro printer owner gets a boost from premium filament cleaner. ...This innovative tool is specifically designed to work seamlessly with printers featuring dual drive extruders, such as the popular Ender 3 Pro model.

This is a cover for the x axis stepper motor with slot for capricon tube to guide filament from the front of the printer. ... i have this paired with this design here https://www.thingiverse.com/thing:3419659

Ender 2 - Filament Holder Extender Check out this tutorial on YouTube at https://youtu.be/mEyUU9S1J3Q. The standard width of the Ender 2 Filament Holder is 80mm. However, I use filament spools with a wider diameter of 94mm. To accommodate these...

I created a straightforward tutorial to ensure my filament filter doesn't interfere with threaded rods. ...The guide features three distinct designs, each with a varying gap placement, as well as a fourth version that omits the gap altogether.

Filament guide. The model was taken as a basis https://www.thingiverse.com/thing:3059604. ...I adjusted the new mod to the dimensions of the CR-10S PRO V2 printer, made a cutout for the bolts on the side.

I designed a casing for filament spools, because especially with new and full spools the filament often got entangled when it slipped over the spool's outer diameter. This then led to printing failures. The casing tends to prevent that and it fits...

A large feeder wheel guide to suit the CR10 V2 With the larger wheel its easier to monitor the filament movement Can be used with the 608ZZ bearing that can be purchased on eBay very cheaply or can print out the replacement bearing in place of the...

Parts required: one M6x30 bolt or a printed axle one 17x6x6 bearing This part is retained under the filament switch itself and clamped by the original 4 screws. There is a quarter-circumference guide to keep the filament on the wheel. The big wheel...

I've seem similar roller guides but I wanted to design one that will let me remove the filament from the roller without having to unload the filament from the hotend. This allows me to remove the roller while loading the filament if it's giving me...

Screws into filament arm the same way the stock one does, but with almost zero friction on the filament roll. Print with bottom of the frame on the print bed, and the roller upright on one end. The bottom of the "threaded" part that screws...

Most filament guides for the CR10s Pro are push fit designs, but I've discovered that PLA loses its grip within a week or two in situations like this. So, I designed one that attaches using two of the existing screws from the printer's filament...

Its purpose was to protect the inlet of the extruder from wear caused by the filament rubbing against it. I had an extra 22mm OD, 8mm ID, and 7mm wide skate bearing that served perfectly as the rolling element. To ensure a proper fit, if the slot is...

Filament holder to improve the pulling load of the Extruder using the original bracket that comes with the printer. You only need to drill two extra holes. Please see pictures for more info. This is reversible at any time. ... For more info visit ...

... printer, requiring zero hardware whatsoever - a sleek and genius design that effortlessly slides into place. This ingenious device cleverly rides along the outside of the gantry, leaving ample space for the filament-out detector on my trusty CR-10.

This small device helps protect the filament from contaminants such as dust.A piece of sponge, pre-lubricated with a small amount of alcohol, is inserted into the filter.Tighten the cable tie into the special recess located in the middle of the...

Summary This is a remix of the Filament Carousel from BansHacks https://www.thingiverse.com/thing:3542220 https://www.thingiverse.com/thing:3559323 It ist just a simple braked to mount the carousel to the Ender 3 spoolholder mount. ... To mount the...