creality filament sensor 3d models

A Filament Sensor Cover for the Prusa i3 mk3 Bondtech extruder upgrade, with space for a threaded brass insert to be pressed in to allow for the attachment of a Bowden tube. ... This allows for its use in the original prusa enclosure.The space for the...

I also used the Idea from Sebastiandruckt ( https://www.thingiverse.com/thing:4813860) to reduce the Gap for the Filament to 2.4mm, so it does not Stuck between the Sensor and the Guide. You will also need the key.stl from blaiseb's design that...

I fitted a Sprite Pro Extruder to my Ender 3 Max, I already own an Ender 3 S1 Pro and wanted to mount the filament run out sensor in the same place as on the S1 Pro. Using this: https://www.thingiverse.com/thing:5419960 I then created the plate to...

This mount is designed for a filament run out sensor, compatible with the Wanhao I3 or Monoprice Duplicator I3 series of printers. Currently, it's mounted on an I3 Plus but should fit the V2.1 as well. I made this mount to work with most sensors,...

Re-drew Woyta94's direct drive mount to include a mount for the A30's filament sensor as well. For the A30, if you're using auto bed leveling and the stock cabling like I do, make sure that you get a left-handed MK8 or the ABL sensor won't fit. I'm...

Found NDSMaker's runout sensor holder that mounts to the x carriage and decided to merge the two.2x spacers and the guide wheel are needed from ChrisIrwin's design.2x fasteners are needed from NDSMaker's design.Compatible filament runout sensor:...

The filament is easy to pull through the PTFE tube and sensor in pretty much any orientation I try.Additional things needed:2x M3 heat-set inserts2x M3 20mm screwsshort piece of clear filament (optional)2x 10mm M5 screws (maybe)Tips:Use a 2mm drill...

It is designed for the dual gear extruder found here: https://www.amazon.com/gp/product/B08D9CNHVN/ref=ppx_yo_dt_b_asin_title_o01_s00?ie=UTF8&psc=1 If you are using the stock extruder, then download the filament_sensor-bottom2.stl file instead. ...

It was kind of hard loading filament with this thing so I made it so you can flip it down to load filament. ... Hardware Required: (2) M3x5 (1) M3x30 (1) M3 Nut (1) Skateboard Bearing It's a tight fit for the bearing to this part, lightly...

In pins_ANET_10.h, comment with "//" #define SERVO0_PIN 27 (or maybe replace "27" with "-1" to steal the servo pin?) and define filament sensor pin here: #define FIL_RUNOUT_PIN 27 You can find my Marlin configurations in attached text file, tested...

I couldn't find something that fits this end stop so I designed this case for it...it also has PTFE tubing holes to help to mount this thing to your extruder and or guide the filament to through it the thing has a tolerance of 0.5mm with except to...

Version 1.1 - you can find it here: https://www.thingiverse.com/thing:4298372 =========================== When I swapped out the standard extruder for the dual-gear one, I realized that filament sensor sitting on the extruder's arm needed to be...

I redesigned the Filament sensor bracket for CR-10 to utilize the same sensor after upgrading to a bondtech extruder mounted in bowden configuration. To adapt this setup, simply swap out the printed part within the E3D adapter on the bondtech with...

I'm not satisfied with the blade switch filament sensor that comes with the Cr-10 and its mounting system, so I combined my three preferred attributes to create a new design. I wanted a roller switch-based sensor that would prevent uneven material...

I'm not going to go over the firmware settings or connections to main board here as they are very well documented elsewhere and this is more about this design of sensor rather than a tutorial on how to add a filament sensor. Once the main section...

I've modified this filament sensor design to accommodate a bowden tube that will guide the filament through it. To begin with, use either the default ender 3 bowden tube or some capricorn tubing like I did, and drill out the inside to make it...

The combined extruder folder with original CR10S filament sensor has been merged into one convenient unit. 2. This assembly includes a handle where you can easily attach cables for seamless connectivity. 3. The redesigned CR10S filament sensor box...

This is a filament sensor that uses an off the shelf M5Stack OP.180 optical endstop. The sensor has an internal pull up resistor that will negate the need for any other electronic components. The sensor is active low, and will pull the sensor line...

Knowing that I wanted a filament sensor for my new Voron, I wondered if I could figure out a way to use this filament sensor with a Clockwork 2 extruder and thus this project was born. I researched the original project...

You will have to adjust the PINS according to your printer’s main board. First, start by printing the needed pintables: Filament Runout Sensor: https://www.thingiverse.com/thing:3142660 Filament Tangle Sensor/Runout Sensor:...

Filament Sensor Mount for the Ender 3 - A Simple yet Effective Solution Are you tired of dealing with messy filament threads on your Ender 3? Look no further! This ingenious mount not only keeps your workspace tidy but also serves as a reliable guide...

I also thickened this section and increased the gap between the rod cut-out and the mounting holes 3) False triggering Some of my filaments false trigger the filament runout sensor whilst others do not - I believe it's down to the tolerance of the...

My design was based on this model: https://www.thingiverse.com/thing:5392146/files I just made some changes to fit those cheapo ali express filament sensors...

This is a filament runout sensor mount and guide for the CR10 with a BMG extruder. Runout switch can be purchased on Amazon. https://www.amazon.com/gp/product/B00MFRMFS6/ I tapped the holes of the switch for M3 screws, but you can use M2 with...

This is a mount to attach the BTT Smart Filament Sensor to the BIQU B1. The mount is designed for use in combination with the BMG extruder and closely aligns the filament path. Print as orientated in the picture. No supports are needed. 25-30%...

This is my concept design using an indirect laser filament sensor based on the LASER filament sensor from the Duet, taking inspiration from the laser filament monitor for the Duet boards but with an innovative twist - indirect reading. I scoured my...

Lastly, the filament sensor negates the need for a filament guide as it feeds the filament straight down.*I will update the file if I find something wrong with it or something happens that needs fixing and will put any of those updates below this...

This is a very simple filament runout sensor to be added to your Prusa mk2s.  I have choosen, for reliability reasons to use an endstop switch instead of an optical sensor.They are very cheap, easy to find on...

Wanted a simple easy-to-print design to mount the BTT Smart Filament Sensor before my extruder on my CR10 S4, Ender 3 Pro, and Ender 3 V2. It is designed to line up with the Winsinn dual gear extruder and has not been tested on any others yet. ... -...

Modelled BTT Smart Filament Sensor Cover. Ready for you to modify, add mounting features, and print! BTT provides STLs, this has been checked against this and a real part for accuracy. The counterbore holes are modified for improved use when...