creality ld 002h 3d models

Simple exhaust for Creality LD-002H. Magnets are small 1 x 5 mm. I doubled them and works for me. A fan should slide in fairly snug, refer to the photo. ...I used an 80mm Noctua fan for less noise.

duct designed to mount an extra filter on the original printer exhaust fan to avoid resin odor designed specifically for the Creality LD-002H printer and a 7cm diameter filter, in my case I used one of the brand cabel (available only in mexico) note:...

Vat Cover for Creality LD 002H I designed this cover to stop dust, fluff and stuff getting in my resin that's left in the Vat after printing. I printed this in PLA but you can print it in any material you like. it uses the clamp down thumb screws...

A simple side mounted fan for the Creality LD-002H

Egouttoir pour imprimante résine Creality LD-002H, inclinable de 45° à -45°

La compra de dicho diseno es solo para uso domestico y recreativos, no es autorizada para fines comerciales "OFERTA GRATIS HASTA EL 13 DE AGOSTO." "DESPUES 50.01 MXN" CREALITY LD-002H Resina Modelo 3D de una extencion para la Creality LD-002H...

Remix of Creality LD-002R AnyCubic Wash and Cure Adapter from goldentuna1200 to fit the new Creality LD-002H

Just a sensible solution to fix the embarrassing Creality's take on the filtration system for the LD Series.

The new version (v2) is available here: https://www.thingiverse.com/thing:4790061 ------------------------------------------------------------------------- Just a sensible solution to fix the embarrassing Creality's take on the filtration system for...

The fan screws on top of 1 & 2, then 3 slides over it, using the little gap for the wire. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 0.2 Infill: 20 Notes: Printed in PLA Category: 3D Printer...

Just a simple slip on Vat tank endoscope mount for the Creality Ld-002H resin printers. Ill upload new versions as I test the angles and whatnot, then include a version for LD-002R. ... Live video of it printing can be found here: ...

Inspiriert von https://www.thingiverse.com/thing:4702213 Here is a suction unit for the Creality Resin LD-002H / LD-002R resin printer. For 60 mm tube inner diameter, 12 mm round magnets. To print it better, two separate files. The Cover...

La compra de dicho diseno es solo para uso domestico y recreativos, no es autorizada para fines comerciales CREALITY LD-002H Resina Modelo 3D de una extencion para la Creality LD-002H destinada a: Reducir el desperdicio de resina Facilitar el Proceso...

Just a sensible solution to fix the embarrassing Creality's take on the filtration system for the LD Series. The new version here (v2) makes the enclosure more compact; I also added a grill on the top, which you can print or not, it's not essential...

Still testing design

Suporte utilizado para deixar a plataforma de impressao escorrendo a resina. Pode ser deixado instalado durante a impressao, é encaixado apenas com grampos de pressão. Imprimi em pla para controle dimensional. Support used to leave a printing...

This is a remix of https://www.thingiverse.com/thing:4766858. ... For some reason I was having problems slicing the original with Simplify3D.

Its an air purifier for the LD002H. It was highly influenced by Peeshow's Air Purifier Plus v2, which I printed. I was printing on an FDM and found it needed quite a few supports and also had quite a lot of tolerance where things went together, so...

This is a z-axis trigger for the Creality LD-002H, extended by 2.6mm to account for the Wham Bam magnetic build system.

Better looking part for the R uploaded.*** This is a reupload of a favorite print for my Creality LD-002H. Will work for the R series. Ive seen a few of these drip assist things and never one that allowed me to keep it on while printing for EXTREMLY...

Bei drucken des Verbinders Teil 2 oder Teil 5 ist Stütz- erforderlich hier hatte ich aber das Stütz dann auch in den Löchern daher dann stütz- blocker, achtet darauf den passenden Rohrlüfter gibts hier https://www.thingiverse.com/thing:5220878...

I was requested to create a body with a finer mesh on the bottom to better restrain the pellets.

Dichtring VAT Tank LD002H creality Mir ist der Dichtring vom VAT Tank kaputt gegangen da habe ich diesen gezeichnet und gedruckt mit TPU A95 und Raft, dieser passt sicher auch in ähnliche Tanks Durchmesser ca. 145 mm --------------- Sealing ring VAT...

LD-002R / LD-002H Handle byphipiis licensed under theCreative Commons - Attribution - Non-Commercial - No Derivatives license.English :In order to be able to remove the cover of the Creality LD-002R printer more easily, I have drawn this handle which...

(M4-M5 Schraube) Italiano : Per poter rimuovere più facilmente il coperchio della stampante Creality LD-002R, ho disegnato questa maniglia che può essere stampata direttamente su questa stessa stampante 3D. (Vite M4-M5) Español : Para poder quitar la...

(M4-M5 Schraube) Italiano : Per poter rimuovere più facilmente il coperchio della stampante Creality LD-002R, ho disegnato questa maniglia che può essere stampata direttamente su questa stessa stampante 3D. (Vite M4-M5) Español : Para poder quitar la...

This is an add-on for the Creality LD-002r resin printer to help drain the resin from the build plate (and model) after a print. UPDATE: I haven't personally tried it, but others in the comments have said that it also works for the LD-002H. Thanks to...

Print 1 and 2. The join in the middle is on an angle, to prevent light leaks. The lid itself is quite thin and fits perfectly. ... File "full" is included just for reference.

<p>Build plate is held at 45 degrees on roll and 15 in pitch, so the dripping is faster. ...No supports when printing.</p> Category: 3D Printer Accessories