creality test prints 3d models
1343882 3d models found related to creality test prints.prusaprinters
The example in the screenshot was done with 20% grid infill.This will work on the Ender-3/5 (220x220mm) & Ender-2 (150x150mm) or other printers with similar bed sizes.Print SettingsPrinter Brand:Creality Printer: Ender...
thingiverse
Similar to the [full bed print](https://www.thingiverse.com/thing:3336550) that arrives on the bed of Tevo Tornado printers, I wanted to create a full bed test print for the Ender-3/5. Print with zero top & bottom layers, three perimeters, and...
cults3d
I've had my CR-10 S5 for a little over a month and haven't had good success in printing smaller objects because the print bed resembles a topographical map of the Rocky Mountains. I haven't gotten around to trying manual mesh bed leveling or the...
thingiverse
I've had my CR-10 S5 for a little over a month and haven't had good success in printing smaller objects because the print bed resembles a topographical map of the Rocky Mountains. I haven't gotten around to trying manual mesh bed leveling or the...
cults3d
Creality's test print has gone low poly! ...Low Poly version of Creality Ender 3 Dog by alockey.
thingiverse
Creality's test print has gone low poly! ...Low Poly version of Creality Ender 3 Dog by alockey.
myminifactory
1 cm cube with circle and 2cm cube with circle. Used for calibration. X,Y axis printed on the sides, and size printed on the top, keep them for reference once you've got things aligned. Then you can occasionally reprint to see if things are going...
prusaprinters
Creality's test print has gone low poly! ...Low Poly version of Creality Ender 3 Dog by alockey. Print Settings Printer Brand: Creality Printer: Ender 3 ProRafts: Doesn't Matter Supports: NoResolution: 200 Infill: 20 Filament: HatchBox PLA Black ...
thingiverse
Creality Ender alignment prints for digital gauge These are the Companion models to this video: https://youtu.be/AN0MlQMMew0 Since the models are structural, but not particularly load-bearing, I printed the gauge holder in Cura with 0.32mm layers, 2...
thingiverse
A set of designs I put together to test a printers (or print settings) dimensional capabilities, thread printability, print balance, and small part printing with a very small test for close border hairing. The images I have uploaded are after a few...
thingiverse
I added the block as a quick surface calibration test as sometimes slic3r does some odd things with the surfaces. Couple really simple really fast prints. I made these to try out my new printer for the first time I though it would be go to test...
thingiverse
This is a collection of the prints that NASA printed on the International Space Station to test their new printer, as well as a few other useful parts. These models were not made by me, nor am I affiliated with NASA in any way. I just wanted to share...
cults3d
$$$ -> 010 can be used for a print with a nozzle of 0.1 mm $$$ -> 025 can be used for a print with a nozzle of 0.25 mm $$$ -> 040 can be used for a print with a nozzle of 0.4 mm $$$ -> 080 can be used for a print with a nozzle of 0.8 mm $$$ -> 100...
thingiverse
$$$ -> 010 can be used for a print with a nozzle of 0.1 mm $$$ -> 025 can be used for a print with a nozzle of 0.25 mm $$$ -> 040 can be used for a print with a nozzle of 0.4 mm $$$ -> 080 can be used for a print with a nozzle of 0.8 mm $$$ -> 100...
prusaprinters
A bunch of test prints, intended to be used to check the first layer (after you do all other recommended calibrations as suggested by the manual). If you get uneven results, try to adjust your bed and/or use this guide to compensate it in the...
thingiverse
These are some bearing test parts to calibrate for bearing dimensions in models. Each one has the hole and shaft size for the required bearing. ... enabling setting up of slicer software.
myminifactory
... gap test prints. ... The sample parts start at 0.1mm gap and increase by 0.1mm. Use the customizer to generate test prints with other parameters. For holes and columns, use https://www.myminifactory.com/object/hole-column-test-print-customizable-18104
thingiverse
... Use the customizer to generate test prints with other parameters. ... For holes and columns, use http://www.thingiverse.com/thing:42800 Printer: --Afinia H480* Filaments: -- Octave Blue ABS -- Octave Glow in the Dark Blue ABS *affiliate link
cults3d
... Use the customizer to generate test prints with other parameters. ... For holes and columns, use http://www.thingiverse.com/thing:42800 Printer: --Afinia H480* Filaments: -- Octave Blue ABS -- Octave Glow in the Dark Blue ABS *affiliate link
thingiverse
It's a quick and very revealing print test that can help you get the right settings for Acceleration. Acceleration in mm/second/second. ... Similar to the old "max_jerk".
cults3d
It's a quick and very revealing print test that can help you get the right settings for Acceleration. Acceleration in mm/second/second. ...Similar to the old "max_jerk".
thingiverse
This is a simple glue test i designed. I wanted to find glue that would be good. ...Please post you makes and results!
thingiverse
I designed them for my testing video: https://youtu.be/Kxa-qFbMLGE I suggest test printing my final design part - Wall Speed Test FAST V2. With it, you can test overhangs, angles, small details, and ghosting. It is kinda all in one test print. If...
thingiverse
I wanted to test the fit of some #10-32 heatset inserts before printing a large print so I came up with these test prints in vertical and horizontal orientation. ... These heatset inserts are from McMaster Carr: https://www.mcmaster.com/93365A154/ ...