creality3d ender 5 plus 3d printer

For Ender 5 Plus. Should also work on a regular Ender 5, but I don't have one to test, so no promises. A redesigned version of the Dual Gear Direct Drive Extruder Mount that includes a hookup for a cable chain. I also trimmed a bit of material from...

I took the base and gantry adapter for the Micro Swiss direct drive Ender 5 plus and remixed it to be magnetically attached. ...I'm sure it's not perfect, but it works great for me.</p><p>Link to the magnets I used:&nbsp;</p><p><a...

This is a remix of the Y axis MGN12H linear rail mount for the Ender 5 plus that drops the linear rail to the bottom V slot of the 20X40 extrusion. Y axis end stops are included as this drops the height of the X axis back to around the stock height...

...Just use support blockers everywhere else. This will fit an Ender 5 Plus. It has a hole in the back for the drive belt on the hot-end. You may need to adjust your X limit switch slightly to prevent it from crashing when it homing. Good Luck! ...

Does the world need another extruder knob for the Ender 5 plus? The answer is yes, if you use Micro Swiss' direct extruder along with the cable strain relief from Sergentchat https://www.thingiverse.com/thing:4591387 (scale it down to 10 %). ...

Since the Ender 5 Plus has a y-axis motor with the shaft exiting both sides, the Bigtreetech closed loop stepper motor driver (S42B V1) is not compatible. This adapter fixes the controller board to the right-hand side shaft bearing (see pic). You...

Since the Ender 5 Plus has a y-axis motor with the shaft exiting both sides, the Bigtreetech closed loop stepper motor driver (S42B V1) is not compatible. This adapter fixes the controller board to the right-hand side shaft bearing (see pic). You...

LCD Screen Frame for Creality Ender-4 3D Printer Print Settings: Layer Height 0.2 mm, Infill Density 20 Percent

Ender 5 plus Bigtreetech btt tft35 inkl ESP01 wifi modul mount Achtung ! in der ersten version war ein fehler !! bitte nur noch die v1.1 und neuer verwenden. Attention ! in the first version there was a mistake !! please only use v1.1 and newer.

This case is to allow you to put an 80mm by up to 25mm fan like the Noctua NF-A8 fan on the MeanWell RSP-500-24 power supply like what came with my Ender 5 Plus. I also wanted to mount it outside the electronics box for better air flow. The front...

Smooth Fang Mounting Plate - Ender 5 Plus - Micro Swiss Direct Drive - BLTouch - ExoSlide BLTouch Approximate Offsets = X-44.6, Y-6.6 Ender 5 Plus (with BLTouch probe), using a Micro Swiss Direct Drive extruder kit, mounted to an ExoSlide linear...

This case is to allow you to put an 80mm by up to 25mm fan like the Noctua NF-A8 fan on the MeanWell RSP-500-24 power supply like what came with my Ender 5 Plus. I also wanted to mount it outside the electronics box for better air flow. The front...

improved version - now also for wider rolls using: https://www.thingiverse.com/thing:3421762 (thanks for that) on original holder verbesserte Version - jetzt auch für breitere Rollen unter Verwendung: ...

Just a version without the text on the front.

<p>Mount this above your x-axis motor for a spot to zip-tie the cables.</p>

Magnificent tiered compartment. ...This compartment is made for the 3D printer: -Creality Ender 3 S1 - Made for the accessories supplied with the printer and more such as files.

I made a large 90 degree bracket for the 2020 extrusion. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 0,2 Infill: 15 Cubic Filament: CR-3D PLA Gold Category: 3D Printer Parts

... This is a custom cooling solution for an NF-Crazy Plus hotend on an Ender 5 Pro. The NF-Crazy Plus is a Mosquito clone that is wider than the original Mosquito, but also mounts using the stock Creality mounting solution rather than the Mosquito's.

E5Plus Cable support Kabelführung Hotend Ender 5 Plus Klemco MicroSwiss original Hotend English A friend of mine, Johannes Loibl, designed this great cable holder. And it's too good not to share with you. Johannes allowed me to share this holder with...

Ich stelle hier mal meine selbst erstellten Halteclips zur Verfügung, mit denen ich meinen Creality Ender 5 Plus mit einer LED Beleuchtung ausgerüstet habe. Die Clips werden einfach nur auf den 20x20er Aluminiumrahmen aufgedrückt. Die Halteclips...

Designed an adaptor plate for the SKR Pro 1.1/1.2 from BigTreeTech, to fit in a Ender 5 Plus. It's designed to dissipate the heat off of the stepper drivers by utilising a 40mm fan on the side. It also mounts a Raspberry Pi on the Top for use with...

This is a redesign from https://www.thingiverse.com/thing:4140386 to the Ender 5 Plus, added an option for a larger relay board, A larger Buck Converter and Added a spot for the MKS UPS. To install follow the pictures above I found it easier to...

Description:This rear frame mount guides the cables and PTFE tube from the rear of the Ender 5 Plus frame to the hot end. This is designed to pair nicely with my filament sensor mount when deleting the bowden extruder. The hole can be used to insert...

I want to put a Raspberry Pi 4B on my actual Ender 5 Plus. I designed this one specifically to fit the Smraza case that I have...

I wanted to put a Raspberry Pi 4B on my actual Ender 5 Plus. I designed this one specifically to fit the Smraza case that I have...

This is a modified x-axis limit switch mounting block that is needed for the Ender 5 Plus with MGN12H linear rails and the Micro Swiss NG direct drive extruder (M3204). See the original creator here: (https://www.thingiverse.com/thing:3960105) ...

This adapter plate replaces one of the noisy default 40mm fans on the Ender 5 Plus bottom plate as well as having a convenient spot for the buck converter. It reuses the same 4 screws that the original fan came with. Parts: 2 x Nuts #4-40 x 6mm...

This is a redesign from https://www.thingiverse.com/thing:4140386 to the Ender-5 Plus, added an option for a larger relay board, A larger Buck Converter and Added a spot for the MKS UPS. To install follow the pictures above I found it easier to...

(5m is enough for 2 sides.) Ender-5 Plus (Creality Official Store) https://bit.ly/3qH6m8C AliExpress https://s.click.aliexpress.com/e/_Adwr40 Amazon...

(5m is enough for 2 sides.) Ender-5 Plus (Creality Official Store) https://bit.ly/3qH6m8C AliExpress https://s.click.aliexpress.com/e/_Adwr40 Amazon...