crossfire 2 3d models

https://vimeo.com/79370836 Fpvlab.com Thread:http://fpvlab.com/forums/showthread.php?25717-3D-Printed-Crossfire-2&p=433303#post433303 So what is new with the Crossfire 2? In general, a lot! It looks like the same ol' Crossfire but its not. I took...

https://vimeo.com/79370836 Fpvlab.com Thread: http://fpvlab.com/forums/showthread.php?25717-3D-Printed-Crossfire-2&p=433303#post433303 So what is new with the Crossfire 2? In general, a lot! It looks like the same ol' Crossfire but its not. I...

Shock absorbing feet for crossfire 2 Quad https://www.3dhubs.com/almere/hubs/kidman-nicholson

A Remix of the Crossfire 2 Arm (v3) and Upper Arm cover to hide/protect ESC and wiring. Weight (50g) for Arm and (28g) for Upper Arm Cover. Replaced Nut catch on bottom plate side with a Nut slot 4mm deep into arm frame. This removes the potential...

I've designed this piece to mimic the screw hole positioning on the top plate of the crossfire 2 so that it can act as an anti vibration clean plate with the use of anti-vibration bobbins or home made silicon tubing. Bobbins:...

Check out the whole "T" copter family: TX8 Octocopter T6 Hexacopter T4 Quadcopter (10" props) T4 Quadcopter Mini 315 (7-8" props) T4 Quadcopter Mini 250 (5" props) Tubular Crossfire 2 quadcopter I've added a post on the forums over at DIY Drones for...

Trying to add a mount for the Pixhawk to the Crossfire 2. The only problem is their are no native files for the onmimac mounts. I have converted the pixhawk mount from STL to SKP; but in the end there were little holes in it that netfabb couldnt...

This is a remix of the crossfire 2. https://www.thingiverse.com/thing:234867 Please consider it a work in progress. This is an experiment to try and lighten the craft, and to provide stiffness for the arms. While this is still under...

This is a flashkill for a vortex crossfire 2 in 35mm.

A cover plate between top and bottom plate of the Crossfire 2 drone Print Settings Printer: Makerfarm Pegasus 10 Rafts: No Supports: Yes Resolution: .2 Infill: 20%

For mounting the pixhawk to the crossfire 2 using MikeyBs original design. just tweaked for the layout for the pixhawk. ...Works Perfect.

Ballon drop contraption for Crossfire 2. You need M3 screws, some standoffs (mine are from ZMR 250), standard servo and some wire for a servo horn. ...Video: https://www.youtube.com/watch?v=drfwoMZkUVY

A Rebuild (mix) of the Crossfire 2 landing gear that shortens the print time and increase strength Requires (2) 3mm 8mm length (min.) Socket bolts .10mm Reduced Base included for a slight give in tolerance Print Settings Printer: Makerfarm Pegasus 10...

A quickly printed spacer between the Crossfire 2 Top plate and bottom plate that removes the need for nylon spacers. ... It adds a mount for a XT-60 Battery Plug that provides (2) ziptie passthrus for easy mounting Modeled in Fusion 360 Print Settings...

a mount for an Arris CC3D power distribution board: http://www.arrishobby.com/arris-power-distribution-board-pdb-with-osd-bec-output-5v-12v-3a-lc-filter-for-cc3c-naze32-f3-p-3314 use small nylon offset to allow mounting to crossfire 2 top plate.

This is a variation of the Crossfire 2 Top Cover to hold a round GPS (55mm) in the top, and also the push button for the APM/PX4. ...It maintains the Immersion RC socket, and adds a generic hole for adding a small FPV camera.

... to get some clearance between the power distribution board an the plastic part to prevent dust short circuit) 23/Feb/2014: Added 1.4mm spacer Probably will add more types when i need them. Crossfire 2: http://www.thingiverse.com/thing:234867

This is a stronger version of the Skid legs for Mikeyb's awesome Crossfire 2. With the original version (and my poor piloting skills) I was breaking the legs constantly in the same places so I thickened them up a bit in the right places. Crossfire...

Since I have a 210mm circular build plate, I couldn't print off the Crossfire 2 Arms. This made me sad. So I trimmed out about 20mm of the middle of the arm so it would fit. This made me happy. Well I think it did.... My concern is that I am very...

... bump at the back edge : http://www.thingiverse.com/thing:1850931 Modeled in Fusion360. Print Settings Printer: Makerfarm Pegasus 10 Rafts: No Supports: Yes Resolution: .2 Infill: 50% Notes: Printed using Simplify3D using supports @ 2mm / 45d.

Drone Build Component List: Main Flight System o Pixhawk PX4 32Bit Flight Controller + NEO-M8N GPS + Power Module o 4 x AX-4008Q-620KV Brushless Quadcopter Motor (HobbyKing) – CCW o 4 x M3 CW Nyloc Nuts for Motor o Hobbyking Multi-Rotor Power...

Telemetry cover for modified Crossfire 2 Top Cover: http://www.thingiverse.com/thing:1850942 Print Settings Printer: Makerfarm Pegasus 10 Rafts: No Supports: No Resolution: .2 Infill: 50%

Arm for Crossfire 2 quadcopter frame with reinforced mounting stanchions to attach it to the main plates. ... Holes for press-fit M3 lock nuts.

Crossfire 2 is designed to be optimized for the APM controller by mounting to the frame via vibration dampening bushings. So i create this adapter to fit a dampering for the KK2 board and other boards with 45mm between mounting holes. Printed with...

Slightly modified Top Cover for Crossfire 2 Fits GPS and telemetry for AdruCopter 2.8 Ebay kits Print Settings Printer: Makerfarm Pegasus 10 Rafts: No Supports: Yes Resolution: .2 Infill: 50%

Standoff for power supply distribution board mounting under the center plate of the crossfire 2 quadrocopter. ... Simple standoff: high: 7mm outer diameter: 10mm drilling: 3.5mm Print Settings Printer: Vertex K8400 ...

A small gimball for a sony 700tvl camera and small 9gr servos. ... Instructions Printed with 0.25 layer hight, and 40% innfill. mounted on the a modified battery tray for the Crossfire 2.

Modified the Crossfire 2 upper frame plate to accept a velcro battery wrap in the front (for an independent FPV camera & TX). ... Also widened the rear channels to fit a Turnigy 9X 8ch receiver.

Crossfire 2: http://www.thingiverse.com/thing:234867 Print Settings Printer Brand: RepRap Printer: Ooznest Prusa i3 Rafts: No Supports: No Resolution: 0.2 Infill: 40% Notes: Infill does not have to be too high on this, I just happened to use 40% this...

Crossfire 2 by MikeyB http://www.thingiverse.com/thing:234867 It is a challenging project, but very rewarding to finally get flying! Instructions The light protectors were obviously thin wall...