crossmember 3d models

rear crossmember for scx10 wroncho conversion since the scx10 frame width is slimmer i made this crossmember the correct width for my wroncho toyota pickup with ar60 axles

The automotive crossmember part, designated as "Right Hemisphere Deep Exploration," is a crucial component that undergoes 3D tracking for precise manufacturing.

Revised upper deck/crossmember for mud truck. ...Print with 3 walls, 30% infill.

ESC tray/crossmember combo for custom mud truck. Prints standing up the tall way with tree supports. If you print it laying down it fills in the bottom of the ESC portion for some reason and makes it solid. ...Printed with 3 walls, 30% gyroid infill.

The crossmember will serve as a substitute for the standard battery tray, making it ideal for users who have opted to upgrade to an aftermarket battery tray. The V1 version is slightly smaller and less rigid compared to the stock unit, but it still...

Front Crossmember i designed for the tf2. ... Works well with the front radiator support i designed.

A crossmember, equipped with magnets, has a capacity of 10 tons.

This is an alternate rear crossmember for the jeep designed by Eficker it deletes the tail lights and adds D-ring mounts for a heavy haul style.

While coming across keja31's design for the crossmember with the heated insert, I also had the issue that the bowden clip from 3d.print.and.paint couldn't be mounted anymore. ...So I decided to combine both features into one.

The Ford Aerostar has 4 bushings on the lower crossmember under the transmission. This assembly is designed to be replaced as an entire unit from the factory. Replacement parts for this vehicle are non existent, and junk yards don't save parts like...

Front Crossmember for Tamiya 1:14 Trucks. ... This is special for Volvo FH16

rc4wd Trailfinder 2 low profile transfercase crossmember gains 12mm more ground clearance over stock reuses all stock shafts and hardware compatible with link kits

Work-in-progress; adapter to attach the rear crossmember of a Volkswagen Passat Syncro to the three-bolt mounting pads on the rear frame rails of a Corrado SLC.

This jig file allows you to design your very own T5 transmission crossmember specifically for a 1965-66 Mustang, accurately outlining the positioning of the crossmember's chassis holes and the transmission mount relative to the crossmember itself. It...

Didn't have the Plastite screws screws so I made a new crossmember that can be used with M3 heated inserts and M3 screws.. Also wanted something that can be printed on its side as the strength was a concern..

The process begins by installing a rear frame crossmember support system, allowing for the easy removal of the battery tray. ...I relocated my battery to the front of the axle assembly and successfully extracted the original battery tray.

Mounting the Servonaut motor on the latest Tipper Truck from Tamiya can result in a potential issue where the axle comes into contact with one of the crossmembers. ...I encountered this very problem myself, so I created a solution to address it.

high clearance crossmember to suit rc4wd trailfinder 2 mwb and lwb (maybe others) suits overdrive/underdrive transfercase and raises ground clearance to only 6mm below the frame rails in the middle requires no other parts or hardware to install (re...

An LED bar clips to the lower side of the ord hadron crossmember, lighting the print bed. For a complete light length, opt for #5 as positioning it on a 195mm bar may affect z-axis carriage wheels. Picture 1 displays the installed #5 LED strip. ...Enjoy...

 I use 5 or 6 perimeters, 5 or 6 top/bottom layers, and a fairly dense infill.This crossmember will also work on the Gspeed V1C1 chassis rails, though it's not ideal (I do use it on mine). ... Due to the shock towers bolting on you'll likely...

To adapt it for direct drive systems, I repositioned it to sit on the crossmember beam, keeping the filament taut and out of the way. When drawing directly from the spool, the filament naturally spirals, potentially getting caught on edges. This...

Here's a reinforced chassis system designed specifically for the SCX 10 and 10.2 off-road buggies from Traxxas. This sturdy component enhances stability and provides improved resistance to shocks, making it perfect for rugged terrain and high-speed...

Eliimina the rear plastic part of the vanquih phoenix

This structural member, comprising only four formed sheet metal plates in version 001 and just two parts in version 002, offers simplicity and efficiency. The box is machine-welded with 3/16 fillets on the outside, featuring a pre-welded bevel from...

I really liked the original, but felt the clips were a bit thin: I snapped two prints just taking the supports off and I have good easy-to-remove-support settings. I also wanted to use a bolt and T-nut to secure this support to the frame with...

I really liked the original design, but I felt that the clips were a bit too thin for my taste: I snapped two prints just trying to remove the supports and I have good easy-to-remove-support settings in place. I also wanted to add an extra layer of...

A customized version of Harley's design is being developed, tailored specifically for use with a truck based on the more compact Axial AX10 chassis. ...This project involves revamping an existing TCS X-Trail trail truck build to accommodate the new...

A 30-ton capacity crane is needed for lifting heavy loads, using its traversing feature to maneuver efficiently.

Upper chassis brace for custom mud truck frame.

For the custom Mud truck chassis