ctc a13 printer 3d models

Print Settings Printer: CTC Dual Rafts: No Supports: No Resolution: 0.2 Notes: 10% infill for the duct, NO SUPPORTS. Even some fails of the first roof-layer proved to be no problem. There is enough space in the duct. ...30% infill for the bracket and...

The CTC Replicator Dual from factory includes two black tubes to be used as clip-on filament guides, which can loosen and fall down and cause issues with your extruder's ability to dispense filament smoothly. This creation is to replace the...

The CTC Replicator Dual from factory includes two black tubes to be used as clip-on filament guides, which can loosen and fall down and cause issues with your extruder's ability to dispense filament smoothly. This creation is to replace the...

This is a complete CTC Prusa i3 frame. I designed it so all parts can be printed on a 150mm by 150mm bed, except for the 'Y Front' which needs to be 190mm long. All parts fit together using M3 nuts and screws. You'll need to print 18 separate...

My CTC Bizer works seamlessly with a MKS Base 1.5 Board, rendering the control buttons unnecessary. This area is now reserved for housing the fuses associated with the hotend and heatbed. For those seeking a mod for the MKS Base Board, a...

Bauanleitung für einen neuen Tisch im CTC: Teile: 2 Stück 20mm x 20mm x 265mm Aluminiumprofil In diese Profile müssen 12mm Bohrungen gefräst werden! ...Randabstand 10mm (mittig) und 22,5mm 2 Stück 20mm x 20mm x 132mm Aluminiumprofil Beispiel:...

I originally remixed these to prevent the nuts on my CTC from sinking into the particle board when tightening the exterior screws. By coincidence, they also work exceptionally well for holding the nuts in place during disassembly and reassembly of...

I've been searching for a suitable form to pour silicone isolators into the aluminum block of my CTC (Makerbot clone) for quite some time now and unfortunately found nothing. Following this great project:http://www.thingiverse.com/thing:1655134 I...

It works well at my CTC, but you could instead use a 22R resistor, an 18R resistor, or a 15R resistor to give the nozzle more power. Lower values may disturb the motor driver. The motor holder I have is available for rebuilding. I have updated the...

People are using their feet to control 3D printers.

This is my take on the belt mounts/tensioner on the CTC I3 Pro B. It's specifically designed for GT2 20T Idlers with 5mm ID bearings. To assemble it, you'll need a countersunk M5 16mm screw, an idler, and a M5 square nut. Mounting requires a M3...

3D Printer Settings for 8mm Rod Halter: http://www.thingiverse.com/thing:1855144 Print Settings: Printer Brand: Up! ...Printer Model: Up Mini Raft Support: Disabled Support Material: None Resolution: High Infill Percentage: 75%

Description A printer mount to mount your printer on a MDF plate (50x50cm). ...You will need 4 printer mounts, 2 on each threaded rod of the base plate Things needed 4 x printer mounts MDF plate 50x50x2cm 8 x universal screws (SPAX) 4x20mm

I upgraded the footings to utilize M6 Buffers as a foundation, significantly minimizing printer vibration.

You can put this on the corners of your printer to help keep everything in one general location. ...It will make the whole machine move as the motors stop versus just the printer bed.

The Mounting Bracket for a 30 Millimeter Tape is attached to the Side of the Compact Thermal Camera Printer.

The Prusa-style upgrade for your printer is a great way to take it to the next level, and one of the tools you'll need is the y-tensioner provided by your printer manufacturer. ...When performing this upgrade, be sure to utilize the y-tensioner that...

Hello there, pals. ...Check out the Filterbox sitting comfortably alongside the Dual Printers right now. Just add a bit of sponge to get it going and securely attach it to your trusty DualPrinter. Got any queries? I'm all ears. ...Ask away!

... on the base plate. ## Essential Components You'll need four printer mounts and a substantial MDF plate that measures 50x50x2cm in size. ...Additionally, you'll require eight universal screws, specifically SPAX screws measuring 4 by 20 millimeters.

After Using Cbiker's design for a long time, the glue did not stick to the printer housing anymore. Because I liked the design but did not want to use glue anymore, I remixed it with some clips. ... Category: 3D Printer Accessories

... the Y-Motor resides. ... For Spools: http://www.thingiverse.com/thing:1731902 Print Settings: Printer Brand: MakerBot Printer Model: MakerBot Replicator 2X Rafts: No Supports: No Resolution: 0.3 Infill: 20% Notes: GreenTec by Extrudr 195°C/60°/80mm/s

I tweaked the design a notch by eliminating the side compartment and pushing the lower tray up against the front panel's edge instead of letting it drop all the way down to the printer's base - it functions beautifully!

After Using Cbiker's design for a long time, the glue did not stick to the printer housing anymore. ...Because I liked the design but did not want to use glue anymore, I remixed it with some clips.

The spoolholder can be found here: http://www.thingiverse.com/thing:2036248 Print Settings Rafts: Doesn't Matter Supports: Doesn't Matter Infill: 15 Post-Printing Fix with 2x 2.5mm zip ties. ... Category: 3D Printer Accessories

To print on the backside of a printer, you'll first need to create two copies of your file - one regular and one mirrored. This will allow you to successfully print on both sides of the paper. ...Have fun!

Adding a simple bracket allows you to securely attach a fan directly to your printer. ...With the motherboard heatbed consistently running hot, installing a fan made all the difference and effectively solved the issue.

... The printing process took place on a Geeetech Prusa i3 3D printer, which I have used with various other printers in the past. Standard settings were applied during the print, ensuring a smooth finish without requiring any additional support.

This is a mount for the BigTreeTech TFT24 display, designed to work with the BigTreeTech TFT24 display case. It mounts where the old LCD panel would be and covers most of the opening that would've been left. When printing the TFT 24 display case you...

I designed this alternative because one of the originals failed catastrophically when I attempted to remove the extensive cable run on its backside in order to tighten the screw securing it to the printer case. It had been hollow, rendering it...

... from wrapping around the filament holder on my Creality Tool Changer. ...Edit it online at https://www.tinkercad.com/things/ie65ZLdjPSh. Print Settings are as follows: Printer: Creality Tool Changer, Rafts: None, Supports: None, Infill: 30% density.