ctc i3 pro 3d models

CtC is a partnership between various creatives in the fields of textile design, fashion design, product design & communication based in Antwerp, Belgium. This pattern was designed using LECTRA software and can be used to drive industrial...

Accessible via http://www.thingiverse.com/apps/customizer/run?thing_id=52734, follow these steps to create your unique version: set font thickness to 5, insert the message "CTC CHEF 2010", adjust stick width to 8, select the "write/Letters.dxf" font,...

Instructions are as follows: select "CTC CHEF 2016" as the message, set stick thickness to 3mm, use the "write/Letters.dxf" font with a size of 10, set hole radius to 3mm, choose a font thickness of 5 and ensure that the stick's width is 8mm. ...Flat...

Print Settings Printer: CTC Dual Rafts: No Supports: No Resolution: .25mm Infill: 50% Notes: Print with 3 or 4 shells to make the mounting holes strong enough to hold the screw threads. ...You have to notch the lower cover to clear the LCD as it sticks...

I decided to create a Mightyboard Standoff for my CTC printer to make removing the motherboard easier since I'm a self-proclaimed tinkerer who has already removed it once to install the Z axis rail mounts and again to install the missing Mosfet to...

The CTC Filament Guide snaps effortlessly onto a dual CTC 3D printer, no adjustments necessary, encasing existing fasteners securely within its design. Its construction allows for a sturdy and precise installation, reinforced with durable 1/8" BSP x...

I'm using an i3 Pro B, but this design should also work with other similar GeeeTech printers - if so, please add your comments to inform others! I've designed this part to accommodate M3 thermoset inserts in the outermost holes, however it's easily...

X, Yand Z ends for "SA Black Plastic Drag Chain Cable Carrier 10 x 15mm for CNC Router Mill", for Prusa i3 pro B. The Y end on the frame uses the screws for the Y motor support, the Y end on the bed fits with no screws or glue (Rv2 has a hole to use...

Hello, this is a remix of PrintingGulliver's [GeeeTech i3 Pro B Air Duct](https://www.thingiverse.com/thing:2345045 "Title"). I greatly appreciate his original work. I needed a PWM controlled radial fan for my printer and discovered that there were...

This is my version of holder for Geeetech Prusa I3 Pro B. I haven't had a chance to test this model yet, as I'm waiting for parts from China to arrive, but I'm releasing it now in case someone wants to test it first. Hardware: 2 - M3x50 screws for...

After I created my first Geetech Prusa I3 Pro B fan duct, I thought that it could be improved. I created a version with two led's. The rest is pretty the same as my previous version: http://www.thingiverse.com/thing:1788901 I used two ultra bright...

I've got a brand new carriage for the Geeetech Prusa I3 Pro X, specifically designed to work with the E3D Lite6 hotend and Bowden extruder. To get it as close to the hotend as possible, I've also included a bracket for an 8mm inductive sensor. For...

The fan shroud section gets a boost with this remix, which adds a mount section that lets you use the threaded holes on the standard factory metal extruder bracket from Geeetech I3 Pro B. The added mount takes into account the offset of those holes...

This is an attempt to design a simple yet functional extruder-fan for a CTC-printer. The design is tailored for a 4cm fan, requiring no adjustments or modifications. Upon installation, the system secures itself in place, providing stable support.

The CTC Replicator Dual from factory includes two black tubes to be used as clip-on filament guides, which can loosen and fall down and cause issues with your extruder's ability to dispense filament smoothly. This creation is to replace the...

My CTC Bizer works seamlessly with a MKS Base 1.5 Board, rendering the control buttons unnecessary. This area is now reserved for housing the fuses associated with the hotend and heatbed. For those seeking a mod for the MKS Base Board, a...

The CTC Replicator Dual from factory includes two black tubes to be used as clip-on filament guides, which can loosen and fall down and cause issues with your extruder's ability to dispense filament smoothly. This creation is to replace the...

Bauanleitung für einen neuen Tisch im CTC: Teile: 2 Stück 20mm x 20mm x 265mm Aluminiumprofil In diese Profile müssen 12mm Bohrungen gefräst werden! ...Randabstand 10mm (mittig) und 22,5mm 2 Stück 20mm x 20mm x 132mm Aluminiumprofil Beispiel:...

Eight year old CTC replicator failing heat at hot extruders. Swapped out heater block, heaters, fitted new thermal couplings still same issue. Swapped out power supply.Found three capacitors on the. 24 volt output were bulging. Also the fans were...

I made this filament pulley for my CTC A8 printer. It reduces chafing of filament significantly on display. The pulley is positioned above the display. It must spin freely at all times. Additionally, you'll need a metric screw with nut (2.6mm shank...

I wanted to install a Reprap discount full graphics smart display on my CTC Dual printer without making any new holes. The available options didn't fit at all. So here's my first solution: It involves creating a cover that replaces the old display...

This meant when I moved the filament spool from my CTC printer to my Prusa, I'd often have excess oil left on unused filament, making a mess when unloading it. To avoid putting oiled filament into my Prusa printer, I decided to design this oiler...

I originally remixed these to prevent the nuts on my CTC from sinking into the particle board when tightening the exterior screws. By coincidence, they also work exceptionally well for holding the nuts in place during disassembly and reassembly of...

Ein Spulenhalter, welcher bei dem Alu-Umbau dirket an das Alu-Profil angeschraubt werden kann, wo auch der Y-Motor sitzt. Für Spulen: Durchmesser-Aufnahme<45mm, Breite bis 75mm CTC-Alu-Umbau -> http://www.thingiverse.com/thing:1731902 Print...

Here is the rewritten text: Ikea Support for Printers ctc:\r\nLEDBERG\r\nLED Lamp, White\r\n$12.99 / 3 pieces \r\nhttp://www.ikea.com/en-us/catalog/products/80267825/\r\nThe writing was placed on one side of the support because I wanted to put them...

First trial to stabilize the Z-axis thread shaft of the CTC printer. The Z-axis is stabilized by lateral plain bearings, but wobbles very strongly and reduces X and Y positioning accuracy. This solution may also be usable for identical Makerbot and...

... better printers. Considering the limits of my CTC equipment, I'm very satisfied. For more cooling power, one might check on the latest thing: http://www.thingiverse.com/thing:1905135 Print Settings: Printer: CTC Dual Resolution: 0.2 Infill: 10%

I have taken the designs of Bernbout and kb3lnn and combined them so I can easily add vibration dampening feet to my GEEETech i3 Pro B without making any modifications to it to actually mount something underneath. These feet together with decoupler...

... remove the push fit connector without removing the hotend. Printing Settings: Printed on a Geeetech Prusa I3 Pro B printer, No rafts are used, Supports are enabled and will touch the bed only. ...Resolution is set to 0.2 mm, Infill density is 50%.

Printer Settings Printer: Geeetech i3 Pro B with an 8mm Acrylic frame Rafts: No Supports: No Resolution: 0.1mm Infill: 50% Notes: Print with a material that has low friction and slides easily on steel. ...I used Taulman PCTPE (which is a Nylon...