ctc i3 pro 3d models

Not sure if it will fit other i3 builds, but it's made for the current CTC Prusa setup. Hope it helps and enjoy! PS: This was all part of preventing slippage on the y-axis that was causing shifting layers. Turns out the biggest culprit was the...

A Tool for Cutting PTFE Tubes in the CTC Extruder. ... 33mm Length for Original Nozzle or Drilled MK8 Nozzle, or 24mm for MK8 Nozzle. Print Settings Printer: CTC Rafts: No Supports: No Resolution: 0.2 Infill: 20%

CTC A13 spool holder for the side, including spool rod from: https://www.thingiverse.com/thing:3646853 CTC A13 Spulen Halter für die Seite, inklusive Spulen Stange von: https://www.thingiverse.com/thing:3646853

This is a remake of the CTC spool holder that came with the printer Its only one piece, no threads required. ... I have printed using ABS on the CTC replicator clone.

CTC A13 spool holder for the side, including spool rod from: https://www.thingiverse.com/thing:3646853 CTC A13 Spulen Halter für die Seite, inklusive Spulen Stange von: https://www.thingiverse.com/thing:3646853

CTC Dual Spool Adapter for Lower Friction on 30 and 34mm Rods, Compatible with all 52mm Filament Spools. ... Printer Settings Printer: CTC Dual Rafts: Not Necessary Supports: Enabled Resolution: 0.2mm Infill: 10% Notes: Two Outer Shells

Weil das vom Ender 3 beim CTC A13 extrem gewackelt hat, habe ich es etwas angepasst. ... Because the Ender 3 on the CTC A13 wobbled extremely, I adjusted it a bit.

Weil das vom Ender 3 beim CTC A13 extrem gewackelt hat, habe ich es etwas angepasst. ... Because the Ender 3 on the CTC A13 wobbled extremely, I adjusted it a bit.

Endstop assembly for the end switch mounted on the rear wall of the CTC to the Z-axis.

Insert filament holders into the 3 cm holes located at the rear of your CTC 3D printers.

I designed this for my CTC dual extruder, but it might just as well fit a Wanhao 4s too.

To Enhance Cooling for CTC Printers: Installation Instructions. ...Fitting the Enhanced Cooler Unit with a Supportive Fan Design.

... machines. One has a longer cable than the other. This part is suitable for printers with the longer cable. If the cable on your ctc-10s is shorter you could use my other design which can be found here. ...https://www.thingiverse.com/thing:4923655

... CTC Printer On Its Pre-Drilled Holes (43.5mm Center To Center). Print Settings: Printer: CTC Rafts: Doesn't Matter Supports: Yes Resolution: 0.2 Infill: 50% Notes: Depending On How Good Your Printer Handles Overhang, Support Might Not Be Needed.

I crafted a personalized remix of Makken104's Ender 3 Fan Cover specifically tailored for the CTC A13 3D printer clone, ensuring seamless compatibility and optimal performance.

Modified the Anet A8 Z motor housing to be compatible with the CTC's plywood frame, which features smaller mounting hole diameters and shorter stepper motor screw lengths.

27 printed chain links\nPrint Settings\nPrinter model: CTC\nRafts: disabled\nSupports: not enabled\nResolution: set to 0.2mm\nInfill density: 10%

I'm a large CTC Drucker that has two big holes at the back for the filament rolls. ...This is the matching cover to close them up.

Easy-to-use CTC Replicator E3D V6 Mount, designed for direct drive performance. ...Print with ABS and utilize the latest revised files.

So I created a vital upgrade 3D printed part that I call CTC A8 Y Axis Belt Clamp for CTC A8. This 3D printed component I designed specifically to address the problem of adjusting the tension on the belt on a 3D printer without disassembling it. I...

...... Print Settings Printer: CTC Dual Rafts: Doesn't matter Supports: No Resolution: 0.1 Infill: 30% Notes: I've used four pairs per side, so sixteen 3mm acrylic mounts will need to be printed with an M5 mounting hole. ... This should help post-printing.

... (link to Rossmann picture frame, 18x24cm, 1.49€) English: Offset clip for the Z-axis for thin glass plates from a picture frame (e.g. ...Rossmann 18x24cm for 1.49€) Print Settings: Printer: CTC Dual Rafts: No Supports: No Resolution: 0.3 Infill: 40%

... ...I've seen similar holders here on Thingiverse and created my own based on them. M10 Bolt (Bauhaus) M10 Nut Beveled Roof Board Print Settings Printer: CTC Dual Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.2 Infill: 40% Notes: PLA

You can easily attach a mirror to the dual extruder of a CTC printer, and possibly even a Flashforge or Replicator. If you have a remote setup with Octoprint and a webcam watching over the print bed, the mirror will give you a great view from above.

... guide that would fit my CTC, so I decided to make one myself. ...This is a simple press-fit design for Teflon tubes with a 4mm diameter, which should work perfectly with the black CTC printer's pre-drilled holes (measuring 43.5mm center to center).

... pass the Flesch-Kincaid test with a score of 100%: Check out this super important tool. ...With this shovel and a regular brush, you can easily clean out the inside of your CTC printer. And it's not just for spring cleaning! ...Have a blast doing it!

CTC Bizer Series includes: Hook Clip: https://www.thingiverse.com/thing:1242159, Spool Mount Hook Clip: https://www.thingiverse.com/thing:1277153, and Filament Spool Mount 1KG: https://www.thingiverse.com/thing:1241858. ...View my other designs at:...

Modified part Modifications: - The shortened mounting sleeve fits the CTC BIZER - Shortened distance between the hole and the mounting wall to the carriage, which eliminated the potential movement of the BLTouch sensor. ... Plug and Play part

... Original Housings Are Difficult to Remove During Assembly. ... This Solution Eliminates the Problem. Print Settings: Printer: CTC Dual Rafts: Any Setting is Fine -or- Raft Supports: Off Resolution: 0.16mm -or- 0.12mm Supports: Off Notes: One Shell

Case designed for the original CTC Prusa power supply. There is a location for a connector/switch duo. ...There is a version with space for an LM2596 module/USB socket to be able to power LEDs using the power supply.