curtain pole 35mm 3d models
39143 3d models found related to curtain pole 35mm.thingiverse
... part modeled after a wooden curtain rod holder I had, I was missing a second one, so I used the same design. ...mounted on wall, with a 6mm hole at center designed for 35mm curtain rods I printed at .5mm layer height and 25% infill and 2 perimeters.
thingiverse
25mm Speaker pole clip, designed this for my cousin who runs a disco business and wanted a clip to tidy up the cables running up the speaker pole. ...I used PLA+ but doubt material really matters
thingiverse
This is a curtain pole support that is used for the middle of the curtain pole or can be used for connecting two poles together.
thingiverse
Curtain pole bracket for 13mm poles. ... Printed with a thick wall (I did 4mm) and 10% infill
thingiverse
Needed something to hold the pole for the curtains on a permanently mounted fixture
thingiverse
Adding curtains to the patio doors, I wanted the curtain to be inside the alcove to hopefully preserve the heating. ...So I made this Curtain Pole Ceiling Mount, I made in ABS , works and looks great.
thingiverse
I made a few different spacers to cater for larger/smaller curtain hoops to give more clearance behind the pole to the wall. I also provide the spacers separately for more flexibility. The hole through the bracket is 7mm and is countersunk...
thingiverse
Its designed to be a little bigger and stronger than the usual bit of bent metal you get with curtain poles for use in bay windows. In a bay window the pole can twist and droop if it can move in the curtain pole support. Print Settings Rafts: Yes...
thingiverse
Super simple curtain pole bracket, designed to replace a broken plastic one from Ikea with same dimensions. Will hold pole up to 25mm diameter. Screw holes are 4mm. Printed flat with no supports, 10% infill in PLA. ...Was meaning to set infill...
thingiverse
This thing is for those cheap curtain poles that droop down at the corner, causing the shower curtain to slide away from the wall, leading to a gap and potentially a soggy floor. This thing simply clips snugly over the pole (approx 20mm diameter),...
thingiverse
My friend's shower curtain pole kept coming down no matter how tight it was wedged into the opening. The walls were tile and were very slick. This holder attaches to the wall with double sided foam tape and allows the pole to be supported without it...
prusaprinters
My friend's shower curtain pole kept coming down no matter how tight it was wedged into the opening. The walls were tile and were very slick. This holder attaches to the wall with double sided foam tape and allows the pole to be supported without it...
thingiverse
This is quick hook i designed to hold the christmas star designed by Paul M https://www.thingiverse.com/thing:35866 It Enables you to pass some string or a power cable and hold in place, and then hook it over a 25mm metal curtain pole as window...
thingiverse
Fit 35mm diameter pole, 2x 5mm screw hole support, 30mm width, 135mm length, 80mm height. If you would like to donate, visit this link paypal.me/sham2951. Thank you. ...Print Settings Rafts: Doesn't Matter ...
thingiverse
There is two version of it: - One version for thinny poles up to 1/2 in (12mm) - One version for poles up to 3/4 in (20mm)
prusaprinters
Portrait iPhone SE mount for a 35mm pole (thread through zip ties to tighten)
prusaprinters
Quest 2 and controller 35mm pole mountsthrough-part zip ties to tighten
prusaprinters
Zip tie channels to securely hold onto the 35mm pole.Solvespace source file included as this is optimised for the case I have for my phone so you'll likely need to change the dimensions for yours.
thingiverse
...I flip this 90 deg making the screen mount flat for printing and add a little support to the 35mm hole. An image of the supports is shown. Included are three files one is for a straight mount. The other two are angled up or down 5 or 7.5 degrees.
cults3d
I have remixed the curtain rod holder by remy https://www.thingiverse.com/thing:1979564 added a 45° flanged hole in the center insted of the 6mm hole.
thingiverse
I have remixed the curtain rod holder Remix by effixe https://www.thingiverse.com/thing:1981833 Print Settings Printer: DIY 3D Printer Rafts: No Supports: No Resolution: 0,4mm Infill: 25%
thingiverse
I have remixed the curtain rod holder by remyhttps://www.thingiverse.com/thing:1979564 added a 45° flanged hole in the center insted of the 6mm hole. ...Print Settings Printer: DIY 3D Printer ...
prusaprinters
I have remixed the curtain rod holder by remy https://www.thingiverse.com/thing:1979564 added a 45° flanged hole in the center insted of the 6mm hole. Print Settings Printer: DIY 3D Printer Rafts: NoSupports: No Resolution: 0,4mmInfill: 25% ...
thingiverse
Curtain pole laser mount 29mm inner diameter. Designed for m3.5/m4 screw up to 12mm long. ...
thingiverse
A bracket that the bottom plate of a Tapo camera can be screwed to. ... Curtain pole size is 19mm diameter.
thingiverse
for use with 28-30mm curtain poles (the sort used for eyelet curtains). I printed the first 10cm at a very high infil (80%) to provide enough strength. Later laters were printed with less infil. You will (probably) need support material for the...
thingiverse
bracket for citroen berlingo multispace (2007 model) that allows the holding of a 15mm diameter pole. ... *DOES REQUIRE DRILLING / SCREWING INTO THE PLASTIC AND METAL BEHIND IT TO BE ABLE TO MOUNT*
thingiverse
This is a simple cable clip for 35mm monitor stand poles. ... I printed with PLA, 4 wall counts (will become 100% filled), no supports.
thingiverse
Model has been moved to **Printables.com**: - https://www.printables.com/model/151629 Simple functional [& over-engineered] VESA 75mm mount to a 35mm pole: - **2 x 8mm** bolts for joining the 3 piece together - **1 x 6mm** bolt for fastening on the...