custom kel tec sub 2000 3d models
1148012 3d models found related to custom kel tec sub 2000.thingiverse
The dust cover from Kel Tec for the Sub 2000 is usable, but it's too easily lost due to its size, shape, and color. I reworked their design to allow it to be printed flat, and added a large hole at the top to attach a tag or lanyard. ... Print on...
thingiverse
The Kel-Tec Sub-2000 is a very popular portable weapon, however, the stock is too short for comfortable operation by taller shooters. In addition, existing extender designs are not available, too expensive or not long enough or all three. The...
thingiverse
Bolt on butt pad for generation 2 S2k. You must drill and tap the factory stock to use this or in some way figure out another way to attach it. I used 2ea 3mm x 12mm hex screws. If the screws strip it is possible to fill the holes with super glue and...
thingiverse
I printed in PLA at .1 layer with support. Printed great. You may need to shave a little off the top side to clear the trigger better. ...THIS ONLY FITS IF YOU HAVE THE M*CARBO TRIGGER GUARD
thingiverse
lock designed to prevent patio umbrella from spinning around when tilted to block the sun. designed for a 37mm umbrella pole. May work for sizes ranging from 36-38, but not tested. If you found this useful, please donate what you think it is...
thingiverse
Magazine loader for KEL-TEC 30 round 22WMR magazines. It has "PMR30" on one side but can be used on any of their matching magazines. ... I printed it in PLA and ABS, both work but the ABS should wear better.
thingiverse
The Kel-Tec RDB is a great rifle but suffers from a handguard that has about 1mm of movement and looks terrible. This was a small project to see if I could make an alternative hand guard that would improve the aesthetics and have a better fit. I went...
thingiverse
I just design a front grip for my ARES Kel Tec RDB airsoft. It’s pretty cool for me, looks not so bukly and reduce a little weight. ...noted that the pin hole may need to slightly polish.
thingiverse
These are pegboard holders for the Kel Tec KSG shotgun. The front support fits anywhere on the rail on the forend. ...The rear one fits between the grip and the tube selector switch.
sketchfab
I saw the Kel-Tec RDB-C the other day and decided to make a .50 caliber version of it. Why? Because everything is beter when it fires .50 calibers. ... And I think it goes without saying, but I still need to texture this.
thingiverse
Grip Plug for Kel-Tec RDB. The design is intentionally hollow for elasticity, infill % will not make a difference. MUST PRINT ON SIDE WITH TAB OPENINGS FACING UP. ORIENTATION SHOWN IN ATTACHED PHOTOS OF PART IN SLICER. For this design to work,...
thingiverse
Gentlemen, I decided to work on some Kel Tec CP33 accessories and this is the first piece, its a P-Rail brace adaptor, I designed 4 versions starting from large and all the way to micro. You will only require 2x M3 x 20mm socket head screws to mount...
thingiverse
Fits all mags securely and functionally is identical to the Kel-Tec +1 Extension that came pre-installed on my older magazines. Slightly tricky to hold the spring compressed while sliding the extension on, a small flat bladed screwdriver helps. ... ...
grabcad
This is the result of sitting down with an actual Kel-tec magazine and taking direct measurements with Starrett dial-calipers and a protractor. Perfect? I'm sure it's not. It should be usable and I welcome anyone to take it and touch it up. I did...
cults3d
This is to extend your grip for the Kel Tec P-11/40 Pistol. It does fit snug and also be sure to print with a high infill I printed my first one with a 60% infill and it was strong enough to hold a full mag but it was my test print my next one I will...
thingiverse
Holds 2 Kel Tec P17 mags Improved retention! ... and nicer design
3docean
The 3D model was created on real base. It’s created accurately, in real units of measurement, qualitatively and maximally close to the original. Model formats: - *.max (3ds Max 2008 scanline) - *.max (3ds Max 2008 vray) - *.fbx (Multi Format) -...
thingiverse
Holds 2 Kel Tec P17 mags Retention needs work I am going to experiment with shock cord around the belt loop and mags for retention. ... Thanks for reading :)
myminifactory
Folding Tail hook brace adapter for kel-tec cp33. ...This is only an adapter, this part is not regulated or restricted and is not a firearm. You will need a M4x30mm screw, M3X30mm screw, and a small spring external diamiter 4mm or less, 8mm x 3mm...
cults3d
Video with sound (For other pistol, but the sound remains the same) - https://youtube.com/shorts/bGzl0JL8zno?feature=share The Kel-Tec PMR-30 is a full-size semi-automatic pistol manufactured by Kel-Tec of the United States. It was made available in...