cyberpowerpc hard drive rails 3d models

This is an universal 3.5' hard drive rail for PC cases. It is made as short as possible to fit 10x10x10 3d printers (crosswise). ... Size is: 4mm x 12mm x 113,6mm Screw holes are 101,6mm apart.

Slide-in mounting rails for a Lenovo C20 computer hard drive. Instructions I needed to mount an additional hard drive into a Lenovo C20 workstation here at the office (I'm the IT guy). I was unable to loacte any of these drive mounting brackets in...

Needed a set of plastic 3.5" hard drive rails. Very simple, but work just fine. -enjoy! ... Instructions PLA, .3mm layer height, 10%infil, 2 outer layers, 50dC bed, and 65mm/s print, 90mm/s travel with...

reversed 3.5" hard drive rails from VisionKJ

Remix of 3.5" Hard Drive Rail 12.5mm by 155mm By FirstDue3D modify with holes to screw into hard drives.

A din clip I remixed from the original so that I hang large amounts of hard drives on a din rail. ...Print it on its side, zero support needed.

If you ever need to remove the hard drive, you can just use the printed rails to pull it out. Or, better yet, just tug on the hard drive itself and it comes right out. Needless to say, these will NOT lock the hard drive inside the server... So if...

... to fit others, but feel free to try. The print time for 2 HDD rails (one set) is about 1.5 hr on 0.2mm layer height. [Note] I have not printed the CD / DVD rails myself. ...It was modified from the HDD rail design and should be ok in general.

These are rails that I quickly made up to support the HD's in a ix4-200d iomega StorCenter NAS I was given, but it was missing the HD holders. ...These are not a match to the originals that would have been with it but they appear to do the job fine for...

I used dimensions from the following two standards: 3.5" disk drive: SFF-8301: ftp://ftp.seagate.com/pub/sff/SFF-8301.PDF5.25" optical drive SFF-8851: ftp://ftp.seagate.com/sff/SFF-8551.PDF You can print either a full sled with a base plate, or just...

I used dimensions from the following two standards: 3.5" disk drive: SFF-8301: ftp://ftp.seagate.com/pub/sff/SFF-8301.PDF 5.25" optical drive SFF-8851: ftp://ftp.seagate.com/sff/SFF-8551.PDF You can print either a full sled with a base plate, or just...

This is a hard drive rail for the HP Z1 all-in-one workstation PC. It fits one 3.5" hard drive. Mirror the model for the other rail. ...The anchors are there to prevent warping and should be clipped off after the print completes.

... sell them without RMAing the whole unit, which wasn't going to happen. You'll need 4 x #6-32 countersink screws to attach this rail assembly to the hard drive. ... I recommend printing this design with a 0.1mm layer height with 100% infill.

My Lian Li 'PC V1000 Plus' caddy had custom bolts to attach the hard drives. All now missing in action! I created a more common 'rail type' that locks the drives in. Took about 4 hours to print full replacements with 2 spare on an ender 3. Quite...

Summary: I designed this enclosure for 4x 3.5" hard drives to be mounted and enclosed easily, while also being on rails for easy insertion and removal for maintenance. I have included my original version 1, and my new version 2 with active cooling...

These are some simple stand offs to mount a hard drive to a flat surface. ...Mounts use (6) #6 wood screws.

These are some simple stand offs to mount a hard drive to a flat surface. ...Mounts use (6) #6 wood screws.

These are hard drive rails for use with an Antec Solution SLK Series Computer Case. I inherited SLK3700-BQE case that, while still in good condition, was missing some parts. I didn't like the idea of putting a mostly usable case in the trash, so I...

Designed these for a friend who has a ibuypower case we did not want to have to buy rails so I designed some. I made a 2.5 and 3.5 size so it should work for both. ...You can print a 0.3 layer height with no supports and it fits great, snaps right in.

Designed these for a friend who has a ibuypower case we did not want to have to buy rails so I designed some. I made a 2.5 and 3.5 size so it should work for both. ...You can print a 0.3 layer height with no supports and it fits great, snaps right...

This is a remix in as much I printed Hard Drive Rail and found some problems, namely with the hollow inside and issues using a screw as there is nowhere for the head of the screw to go. I used his for dimensions. ...This should work with a Cooler...

--- This thing is just really simple rails to mount a 2.5" drive on the bottom of a Raspberry Pi. I made these because I want to start a NAS project, but I kind of didn't know where to begin. So I made some rails to fit the bottom of my Mini...

hard drive

Sample of a hard Drive

its a hard drive from kingston. ...its a case where you can put in hard drives from old computers/laptops likes are appreciated

Dell Laptop Hard Drive Rail Set (Left & Right) 7.0mm Dell Part Number/SKU: 5D56T-N80M Label on part: (EAR-11) Compatible Dell Laptops/Notebooks: - Precision M2800 - Latitude E6430 ATG - Latitude E6430s - Latitude E6540 - Latitude E6330, E6430, E6530...

Fits inside of HP workstation/desktop guide rails so you can keep using the easy rail system instead of tearing apart the case or just letting them hang by the sata cable.

FR _ Hello Here is a simple storage for multiple hard drives. It can be used vertically. Print as many elements as there are hard disks and a cover. Each element can be nested and glued together. ENG_ Hello Here is a simple storage for several hard...

Motor from Hard drive

For 10 hard drives