d cell battery adapter 3d models

I wanted to power a toy racetrack not with 4 D batteries but with a USB wall charger. You can put a nail or some other contact into either end of the dummy and connect it via cable to a USB plug or directly to a power adapter. ...Please pay attention to...

bendrexl designed a nice AA to D cell adapter, however, I did not have a "brass fastener". I do have a bunch of loose screws. I popped the file into tinkercad and replaced the square hole with a 3mm screw hole. ... Simply put a 3Mx12 screw in the...

bendrexl designed a nice AA to D cell adapter, however, I did not have a "brass fastener". I do have a bunch of loose screws. I popped the file into tinkercad and replaced the square hole with a 3mm screw hole. ... Simply put a 3Mx12 screw in the end...

Primarily needed this to augment the D-cell adapters that were included with our Eneloop rechargeable kit. Inspired by Seadevil's elegant "brass fastener" design, this was a re-model from scratch in Fusion 360. ...I reduced the number of fins to...

... the same voltage (1.5V). This will be a useful addition to anyone who has older toys, radios' etc, that require D Cell batteries Simply print the adapter, wad up a little aluminum foil on the negative end, and slide in your AA battery. ...PRESTO!

I printed out and tried multiple adapter from D-Cell to 18650 but none of them worked for my quad D-Cell maglite. Such adapters allow to use your trusty D-Cell Maglite in combination with more modern 18650 cells combined with the lately available...

The quad D-Cell adapter printed fine on my Ender 3 in vertical orientation but if you own one of those 6 D-Cell monsters, you might want to split the adapter in two halfs and glue them together later. After printing out the adapter simply heat up...

(Yes they might not have the current capacity of D-cells, but it works pretty well for what I needed.) Print instructionsCategory: Household Summary I have lots rechargeable AA batteries, and a few things that require D-cells. This will let those...

I have lots rechargeable AA batteries, and a few things that require D-cells. This will let those AA's work in the D-cell applications. (LED camping lantern, mattress pump etc.) and the AA's are small so you can carry extras and replace them as...

This adapts a single 18650 in a 2 D cell flashlight. ...Or print two of everything, to work in a 4 D cell flashlight.

I own some devices using D cell type because high capacity of these cells (+-6000maH) I designed this simple adapter in order to adapt the D cell type to my charger. No tricky soldering needed. You need for the AA adapter side 2 screws M3x6mm 2...

Reference the original: http://www.thingiverse.com/thing:33706 Like Maikalguy's adapter, but I notice the 4xAA package is bigger than a single D cell, and wouldn't fit inside my Mag Flashlight! So this 3xAA adapter is slim enough to fit. I have...

and running out of D cell batteries for the flashlights... :-\ Got a bunch of AA cells... hmmm... Let's put that 3D printer to good use while we have the generator going! ;-) Instructions 10% fill,...

18650 Battery Adapter for 2 C-Cells, 2 D-Cells Infill:15%

Other Mag-Lite adapters available: Mag-Lite 2-Cell C Size Adapter for 18650 Lithium Batteries https://www.thingiverse.com/thing:3465819 Mag-Lite 2-Cell D Size Adapter for 18650 Lithium Batteries https://www.thingiverse.com/thing:3473302/edit...

Other Mag-Lite adapters available: Mag-Lite 2-Cell C Size Adapter for 18650 Lithium Batteries https://www.thingiverse.com/thing:3465819 Mag-Lite 3-Cell C Size Adapter for 18650 Lithium Batteries https://www.thingiverse.com/thing:3473408/edit...

This is a simple D Cell battery

D Cell 3.6 volt battery

It's a holder for six D-Cell batteries.

16 D cell battery organizer, 34.75 MM holes to better fit.

this was supposed to be a AA battery, but I messed up in Sketchup and it came out as a D-cell.

http://www.thingiverse.com/apps/customizer/run?thing_id=1741164 Instructions Using the following options: detail = 90 cell_diameter = 33.2 mount_tab_height = 8 cell_length = 62 holes_pan_diameter = 6.6 capacity_lower_section = 3 calibrate = 0...

This adapter replaces two D-Cells with one 18650 battery. I use it in my Mag Flashlights. You will need two battery tabs I use Keystone 209 clips from Amazon. The negative end I am using a quarter, but you can use a washer as well. I just didn't...

A more generic version of my "V393 to V303 Button Cell Adapter" http://www.thingiverse.com/thing:8410 The file is set up to create a simple crescent shaped V393 to V303 Button Cell Adapter but you can insert sizes for whatever button cells you have...

Battery D Cell 3D model Modeled in Blender. Preview image rendered using cycles. All scene are included in .blend files. All object have been named appropriately. ...Convert to:- - 3D studio - Collada - Wavefront -...

D Cell Battery Box Battery box for 4 D Cell batteries, created by modifying the Battery Box - AA / AAA (v1.2) by Zvedak. Like Zvedak's battery box, it requires two screws (M2.5x15 to M2.5x20). Printed in PLA without supports. <B>Assembly</B> -...

Designed to work with these contacts from Keystone Electronics: [CONTACT BATTERY D NEGATIVE COIL](https://www.digikey.com/product-detail/en/keystone-electronics/5251/36-5251-ND/2745884) [CONTACT BATT D POSITIVE...

http://www.thingiverse.com/apps/customizer/run?thing_id=128069 Instructions Using the following options: build_plate_manual_y = 100 build_plate_manual_x = 100 cells = 3 build_plate_selector = 0 wall = 2.4 custom_length = 3.2 type = D custom_diameter...

D BattBlox is designed for D batteries. The 'blox' has been made to keep 6 D's. Additional Blox can be added as needed. In my case, I have made some in red and some in green. Dead batteries are put in the red Blox, and once they are charged up, they...

Simple type D battery adapter for AA size battery. ... I use rivet pin as the centre battery contact.