d4r ii 3d models
19465 3d models found related to d4r ii.grabcad
Model of a FrSky D4R-II receiver. ...This is the first Rhino model Ihave submitted.
thingiverse
A simple mount for D4R II receiver. ...Use shrink tube or insulation tape to hold antennas to supports
thingiverse
Simple diversion antenna equipped mounting setup for your FrSky D4R-II receiver. ...You will need antenna tubes to accompany this part.
thingiverse
FrSky D4R-II receiver mount to fit the Shen Drones Tweaker frame You need to flip the model 180deg to print because I'm an idiot.
thingiverse
This case will house a FrSky D4R-II receiver and allow it to be strapped to the underside of a plate without crushing it. ...Antenna lead holes can be drilled out accept tubes to protect the leads.
thingiverse
Holder for the ZMR250 Frame and FrSky D4R-II Receiver. Fits to the front or rear. ...Print Settings Printer Brand: MakerBot Printer: ...
cults3d
This case will house a FrSky D4R-II receiver and allow it to be strapped to the underside of a plate without crushing it. ...Antenna lead holes can be drilled out accept tubes to protect the leads.
thingiverse
QAV210 Lisam D4R II holder Build to attach the antennas with 2 zip ties and 2 heat shrink, a clip in the back can hold the following LED: https://goo.gl/JpKZjZ
thingiverse
Tray to hold your D4R-II in your ZMR Frame. Edit (6/7/15): Added New modified tray with VTX holder. Holds ImmersionRC 600mw 5.8ghz VTX. Also have a version to hold XT60. ... Instructions You'll need...
prusaprinters
Also have a version to hold XT60. Print instructionsCategory: R/C Vehicles Summary Tray to hold your D4R-II in your ZMR Frame. Edit (6/7/15): Added New modified tray with VTX holder. Holds ImmersionRC 600mw 5.8ghz VTX. ...Also have a version to hold...
thingiverse
FrSky D4R-II tray in the 36x36 format for stacking on top of similar format flight controllers (ie. Naze32, Flip, CC3D). Requires standoffs, cover or the easy print 10mm standoff tray. See the stacked modelUsage: Stack on top of FC. ...
thingiverse
These parts should help to mount a D4R-II Rreceiver on 36x36 (30x30) holes - same size as some Flight Controls like nanoWii, OpenPilot Revo... Please feel free to modify this project for use with other Receivers. The missing part you'll need to...
cults3d
These parts should help to mount a D4R-II Rreceiver on 36x36 (30x30) holes - same size as some Flight Controls like nanoWii, OpenPilot Revo... Please feel free to modify this project for use with other Receivers. The missing part you'll need to...
thingiverse
As the name suggests, a nice way to place your beeper on a miniquad. ... 30.5x30.5 mounting holes fits D4R, X4R and several other receivers
cults3d
Designed to hold the following on my race quad. ... NeoPixel 8x boardFrSky D4R-II RX This will allow you to also use zip ties plus heat shrink to hold the D4R-II antennas in a V position.
thingiverse
... D4R-II Reciever. ...This mount allows you to securely attach the two devices at the same time. It perfectly combined with d4r-ii reciever antenn holder: http://www.thingiverse.com/thing:824916 Fixed. ...Move the hole, allowing binding D4R-II receiver.
thingiverse
A receiver cover for the ImmersionRC Vortex 250 and 285 and the FrSky D4R-II receiver. ...Parts needed: 2x 3mm antenna tubes 4x 6mm course thread screws
thingiverse
Simple D4R-II case for_vortex 285 Print Settings Printer: DaVinci-jr Rafts: Doesn't Matter Supports: Yes Resolution: 0,1 Infill: 50%
thingiverse
... on my race quad. ...NeoPixel 8x boardFrSky D4R-II RX This will allow you to also use zip ties plus heat shrink to hold the D4R-II antennas in a V position. How I Designed This This was designed in design spark mechanical 2. ...Design file is included.
thingiverse
It's a protection for D4R-II and Aomway 200mW Vtx for ZMR 250 and another multirotor You can attach the antennas with a 4mm plastic tube to secure the bracket , you must screw it on the frame
thingiverse
I uploaded my scad file and 3 different stl files: D4R-II_Naze.stl - base for D4R-II with no holes of the bottom D4R-II_Naze-left-hole.stl - Base with an hole on left side of the base, very useful to give space for the Telemetry, Battery and Buzzer...
cults3d
This is to hold the D4R-II Rx between the two upright poles on the rear of the quad. ... The vertical antenna holders were made small on purpose so that you can either drill them out to fit rods or use zip ties and heatshrink to hold your antenna.
cults3d
This receiver mount allows you to use the FrSky D4R-II receiver without taking it out of the case. The version 2 Top has larger cylinders that you can drill out to 3mm and put antenna tubing in. ... Version 3 Top has sideways antenna tubes
myminifactory
This is to hold the D4R-II Rx between the two upright poles on the rear of the quad. ... The vertical antenna holders were made small on purpose so that you can either drill them out to fit rods or use zip ties and heatshrink to hold your antenna.
cults3d
http://www.thingiverse.com/thing:889408 I used Earthworm's great D4R-II mount, but added a little to the bottom and holes for Zip-ties. Its made to mount on the receiver tray for the ImmersionRC Vortex. ... With this box you need to take the cardboard...
thingiverse
This is to hold the D4R-II Rx between the two upright poles on the rear of the quad. The vertical antenna holders were made small on purpose so that you can either drill them out to fit rods or use zip ties and heatshrink to hold your antenna. ...Print...
thingiverse
With this holder you can easily mount the D4R-II Receiver rock solid to the lower front part of the frame. It is fixed with the frame bolts and a zip tie. This is the long version that can be combined with the bottom VTX Holder for the Eachine ET200:...
cults3d
Custom fit mount to position an FrSky D4R-II receiver within the flight control board stack. Sized to match 36x36 mm (30.5mm Mounting) flight control boards, will nicely fit in the stack with an 8mm spacer and Flight Control or other board on top.
thingiverse
(something else i cant recommend enough) anyway this fits perfectly into this mount side by side to the D4r II rx so there is no need for the compartment to drop down as it does with the immersion vtx, This also allows more space for accessing the...