dan a4 sfx 3d models

Foot replacement for the DAN A4.The aim was to adapt the look of the DAN 4 to my furniture and to improve the air circulation from below.

If you've an AIO in the Dan Case A4 this support holds a 92x14mm fan in place. My mainboard is the Gigabyte B550I AORUS PRO AX and the placing fits for the front M2-Slot. Temperatur drops around 7-10°C. ... Only drawback is a bit turbulence noise...

17-12-2021: new version with a simplifie design and a reduced height 15-12-2021:I was looking forward to gain some space on my desk , so I imagine a vertical stand for my Dan Case A4. It is a first rough version that is working but that I will try...

This is the final version of the Dan A4 (V4) Ultimate Cooling Kit. The following STL files are included, along with their print settings: * PSU Bracket: Print at 0.15 Layer Height, Use 100% Infill, and Build 3 Walls. * Riser Bracket: Print at 0.15...

This bracket attaches to the Dan A4 case frame and covers the top left motherboard mounting screw. It should work with existing motherboard standoff screws. This area tends to be extremely hot inside my computer case. Designed specifically for...

[NEW VERSION HERE: dancase A4-SFX - Fan Partition Standoffs v2.0]The thermal concept of the dancase a4 is simple, but often requires adjustment to improve performance. Note this was kinda thrown-together, so the Solidworks file is a bit messy. At...

The thermal concept of the dancase a4 is simple, but often requires adjustment to improve performance. This mod will partition the front and back case fans so that you can run a push-pull configuration without feeding the hot exhaust into the intake....

Designed up this dealer button to use in home games or have just as something laying around for any poker fan. It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports needed for spade inset. Letter...

This fan duct is crafted specifically to support a 92mm fan due to its slender profile, allowing it to seamlessly integrate into the compact design of the DAN A4 case when paired with the Noctua NH-L9i cooler.

Top mount bracket required for an 80x10mm fan installation in a Dan Case A4 v3. The bracket will friction-mount to the case frame. Using an Akasa Slimfan 80mm x 10mm PWM Fan (AK-FN076). Previous issues encountered with fan rubbing against riser...

... at http://www.thingiverse.com/apps/customizer/run?thing_id=48424. ...To make this unique piece, set the total depth to 10, total height to 60, total width to 95, finger size to 23, and engrave the word "DAN" while spacing each finger by 23 units.

... ...http://www.thingiverse.com/apps/customizer/run?thing_id=52734 Instructions Using the following options: hole_radius = 3 stick_thickness = 2 Font = write/orbitron.dxf font_thickness = 5 message = Dan stick_width = 8 font_size = 10 flat_bottom = 1

... = extruder2 bar_color = Khaki line5 = line4 = line3 = line2 = line1 = Lt. Dan border_width = 0 lug_text_distance = 6.8 textextruder = extruder2 font_name = Black Ops One character_spacing = 0.9 font_weight = 0 whichextruder = monochrome

Mounts a 120mm case fan externally using the existing 92mm slots. You'll have to move the power extension to the lower position. Includes an optional blanking plate with a small cutout to route the fan cables. 92mm mounting holes are sized for M4...

Top-of-the-line Case Fan - Not Yet Tested Under Real-World Conditions!

I made this panel to print on smaller printers. Its a design to snap the 2 parts together. Its a tight fit bit it will work, it could be that you have to file it slightly to make it snap together. After it snapped together you can use a small...

Its a tight fit but it will work, it could be that you have to file it slightly to make it snap together.After it snapped together you can use a small little drop of glue to make sure the mech part is sollid connected to each other.I preffer to glue...

Made for modifikation SFX Polymernut

Adapter for SFX-PicoPSU-Mini-PC with holes for: 60mm Fan Potentiometer Powerplug

Adapter for SFX-PicoPSU-Mini-PC with holes for: 1. 60mm Fan 2. Potentiometer 3. ...Powerplug

Adapter for SFX-PicoPSU-Mini-PC with holes for: 60mm Fan Potentiometer Powerplug Print Settings Printer Brand: Creality Printer: Ender 2 Rafts: No Supports: No Resolution: 200 Infill: 100 Filament: PolyMaker PET Category: Computer

Update 2: Enhanced Base Support - Added 5mm and 8mm Feet These enhanced feet enable the base to rise 3/5/8mm above the surface. ...This design boost allows for improved airflow when utilizing a bottom-mounted fan.

I wanted the front cover to be ventilated. For the GPU cover, I wanted to add more ventilation towards the bottom for the 4080 FE. I had to modify the original clip because it was larger and intended for a spacer adapter. ****** The GPU panel...

Heavenly inspired by the Loser card mod I've designed a new PSU bracket that can hold a 92x14mm Fan. This supports the PSU to get rid of the hot air and also helps a bit in terms of GPU temperatures. This bracket fits the Corsair SF600 and SF750.

Available for sale at the official J-Hack storefront: https://j-hackcompany.com/ -------------------------------------------------------- Compact fan shroud designed specifically for use with a 92mm fan and tailored to fit the Dan A4-SFX. To...

This is a CAD model representing the Asetek 645LT 92mm Radiator designed originally for the DAN A4-SFX case and other ITX sandwich cases. ...Dimensions aren't perfect, but I've tried to make them as accurate as possible using modified photos as...

To Mount Your SFX Power Supply, First Apply Glue to the Insides of the Support Holes and the Small Ridges Nearby. Next, Center the Stems and Place Them Inside Firmly, Ensuring There Is No Gap While the Glue Dries. Let the Assembly Glue Dry Before You...

You're working with a straightforward SFX-ATX Adapter Plate. Possibly you'll need to fine-tune the holes for your intended application. Be cautious, as an extra grounding wire may be necessary between your power supply and case! ... Print Settings...

Supports are exclusively for the SFX case hole. You can print other elements without any need for supports. The base is secured with original screws at the back, and fan screws on the front. I've used Loctite to glue the feet in place, which works...