davinci jr 3d models

Post-Printing Mounting screws I designed this bracket to be screwed onto the DaVinci first, install the board, then screw it down. However, it holds the board securely without any screws. ...After verifying that normal screws can self-thread into the...

Print Settings: Printer: XYZprinting Davinci 1.0 Pro Rafts: No Supports: No Resolution: .3mm Infill: 25% How I Designed This Problem: Filaments were cutting into the spool holder and feed hole in the back of the printer, causing issues with filament...

I fitted an MK8 extruder directly to my DaVinci 1.0A without any modifications, drilling or cutting. I wanted to share this method because it's much easier than the other mods I've seen for the stock extruder. I used the original heater to save time...

This spool holder is designed specifically for the XYZ DaVinci 3D Printer, accommodating spools with an inside diameter of 32mm. The model targets big Octave ABS spools, which measure 160mm in diameter and 100mm wide. This premium spool holder...

Replacing the old fan is extremely easy as you can utilize the same fan and connectors, and the DaVinci repetier firmware lets you control the fan settings for each print individually. Update: I added version 2 that's elevated 2.5mm at the bottom so...

Print Settings Printer: DaVinci 1.0 Rafts: Doesn't Matter Resolution: 0.2mm Infill: 15% Post-Printing I had to perform a significant amount of carving to get this to fit properly. ...I need to update the drawing, but with some effort it will fit...

This modification replaces the stock Davinci extruder on the MK9 for optimal performance. It's crucial to note that it functions exclusively with linear bearings, which must be incorporated into the design for seamless functionality. To facilitate...

This is my fourth iteration of an adapter designed to enable use of an E3D V6 on a DaVinci 1.0A printer. A considerable amount of effort was invested in making this work with minimal modifications. The stepper motor assembly is relocated upward by...

I bought a PrintinZ print bed for my XYZ DaVinci Pro. My binder clips were either too big or too small so I made my own. 2 clamps at 20mm wide go in the front. 1 clamp 10mm wide goes in the back. Print in ABS with 50% infill. There is a brim on the...

Print instructionsCategory: 3D Printer Parts Print Settings Printer: Davinci 1.0 Rafts: Doesn't Matter Resolution: 0.2mm Infill: 15% Post-Printing I had to do a lot of carving to get this to fit. ...I need to do an updated drawing but it will fit with a...

It seems to work better than the stock but isn't up to par with what I expected. Print instructionsCategory: 3D Printer Parts Print Settings Printer: Davinci 1.0 Rafts: Doesn't Matter Resolution: 0.2mm Infill: 15% Post-Printing I had to do a lot of...

My E3D V6 hot end carriage for my Davinci Pro 1.0 I have an old Davinci Pro 1.0. I bought it when they first came out way back in 2015. I pre-ordered it and got a discount. It has been a good printer over the years and of course I have done some mods...

Video can be found here: https://youtu.be/7eT6KxMqU0A Because many people enjoyed my previous gift card, which was a fully 3D-printable wind-up car gift card (https://www.thingiverse.com/thing:3308711 and...

You may need to trim the leads coming out the back of the switches to get them to sit flush on these mounts, but it did not adversely affect anything. The NEMA 17 motors have a longer post but shorter body, so I am including a spacer that gives it...

The issue is detailed here http://voltivo.com/forum/davinci-hwmods/41-squeaking-and-or-circles-arent-round-check-this-56k-warn/reply/7767 and the solution is to replace the pulley with this part and ball bearings and you may also have to replace the...

Since my Davinci 1.0's stock extruder idler became worn down and unusable, I've been searching for an alternative extruder but there aren't many options available.\nI attempted a printed extruder which uses a bearing as an idler that worked well, but...

Martin Luther King Jr.

Customized version of https://www.thingiverse.com/thing:1672381 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1672381

This is an iconic lamp from Pixar and first appeared on 1986

Vinícius José Paixaõ de Oliveira Junior, is a Brazilian footballer with Spanish nationality who plays as a striker for Real Madrid Club de Fútbol of the Spanish Primera División. ...He has been a full international with the Brazilian national team since...

Customized version of https://www.thingiverse.com/thing:1143325 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1143325

This is a customized version of the thing 74322 on Thingiverse. It was created with Customizer, which can be found at http://www.thingiverse.com/apps/customizer/run?thing_id=74322. ... Instructions You are using the following settings: ...

This is an inventive Tinkercad-crafted robotic explorer.

Customized version of https://www.thingiverse.com/thing:1143325 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1143325

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/jywwi8SF5zk

No information is available to describe this individual.