deftech 37mm launcher 3d models
7989 3d models found related to deftech 37mm launcher.thingiverse
Here is my version of the DefTech 37mm Grenade Launcher from the series Supernatural. This is not screen accurate, but it is as close as I could get it with limited information. Print everything at 20% infill. ... All parts are single prints except...
thingiverse
This is only an Airsift prop so please don't add a 1 1/2" Black or PVC Pipe for a barrel as 3D printed parts can not tolerate the high pressures, This is only a proof of concept and functions on CO2 Airsoft 12G & 40mm Grenades (Which are actually...
cults3d
This is only an Airsift prop so please don't add a 1 1/2" Black or PVC Pipe for a barrel as 3D printed parts can not tolerate the high pressures, This is only a proof of concept and functions on CO2 Airsoft 12G & 40mm Grenades (Which are actually...
thingiverse
This is a cleaning tool designed to clean the bore of 40mm and 37mm grenade launchers. Included are two basic versions: 40mm and 37mm. The 40mm includes two different tips, a 37mm and a tighter fit 39mm. I typically use the 37mm which works good...
thingiverse
A 37mm pepper delivery round for a Havoc flare launcher. Fill the finned base with hot glue to secure the wick fuse. Do not adhere the cap over the gun powder holder, as the ignition will cause it to push the ghost pepper cup off of the finned base.
thingiverse
This insert is one of many parts required to make a functional 37mm signaling device. Also, the barrel needs to be bored out to fit a 37mm barrel liner. ... Required parts: Trigger, Firing Pin, Breech insert, Firing pin spring 1x6x58mm Optional...
thingiverse
So here is my attempt at the deathwatch blaster based on the Deftech 1315 gas gun as requested by a follower. It will take a 290mm pvc pipe with 22mm OD to add rigidity. The grips come in combined and seperate . ... The trigger is static ...
thingiverse
Though for reference they have been printed and the test fit to launcher is good as in they chamber properly and the primer pocket accepts a 209 primer and the powder capacity is accurate. Though these shells remain untested, I DO NOT believe they...
thingiverse
They are intended as non firearm parts for a 37mm flare launcher, intended payloads would be making fireworks using flying fish or crackling fuse, smoke with proper vent holes drilled by end user, or OC containers. Please observe and follow all local...
thingiverse
They are intended as non firearm parts for a 37mm flare launcher, intended payloads would be making fireworks using flying fish or crackling fuse, smoke with proper vent holes drilled by end user, or OC containers. Please observe and follow all local...
thingiverse
They are intended as non firearm parts for a 37mm flare launcher, intended payloads would be making fireworks using flying fish or crackling fuse, smoke with proper vent holes drilled by end user, or OC containers. Please observe and follow all...
thingiverse
Customized version of http://www.thingiverse.com/thing:193647 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following options: facets...
thingiverse
37mm projectile for your launcher! ... -Print with the top open and fill with plaster for an inert round -Or print upside down with the bottom open and fill with smoke mix -1:24 RH twist rifled projectile -Optimized for vase mode printing, 45°...
thingiverse
Created 37mm standoffs/spacer to use with my MKS Monster8 cooling fan (https://www.thingiverse.com/thing:5428059) and DIN mount (https://www.thingiverse.com/thing:5428083). ... The hole is big enough to fit M3 screws.
thingiverse
... for use in the construct of display pieces, or used with cosplay costumes. ...Not intended to be used in real launchers! Death and dismemberment may happen if you do. I take no responsibility in the miss use of this design. You have been warned! ...
prusaprinters
Created 37mm standoffs/spacer to use with my MKS Monster8 cooling fan (https://www.thingiverse.com/thing:5428059) and DIN mount (https://www.thingiverse.com/thing:5428083). The hole is big enough to fit M3 screws. Print Settings Printer: Tronxy X5SA...
thingiverse
WARNING! These models are not suitable for real world use out of the box as a 3D printed item. A better though untested option would be using these printed models to make a mold and then casting the models using a more suitable material. This was...
thingiverse
This is a projectile designed to be used with a 37mm flare launcher. The body is printed in two parts so that the top can be filled with appropriate flare material before sealing the two haves together. ...The dimensions of the projectile are such that...