dell 2.5 to 3.5 caddy 3d models

Note that one end has a higher wall, so the drive will only fit properly over the lower wall end. This is a pair of 3.5 drive to 2.5 drive adapter designs. One uses a typical M3 nut (approx 5.3mm across the flats x 2.3 thick). The other is a simple...

I needed a server with 3.5" hot swap trays, but I didn't want to put those outdated hard drives in it. The issue was that 2.5" SSDs don't align with the mount holes. You can't drill below to secure it because it has to be flush to fit in the server.

This holder is designed for two 2.5 inch SSDs in place of a single HDD. There are no screw holes for SDDs, they will slide in and out freely. It is not really designed for 2.5inch HDDs because there is no way to dampen the vibration from them. ...Print...

A simple adapter to fit a 2.5 inch SSD or laptop HDD to a PC case with mounts only for 3.5 inch hard drives.Sadly do not have a photo of this one, since it was specially made for a customer and then never seen again. So here are some OpenSCAD...

Cut the right side down so that the 2.5" disk lines up with the edge of the adapter, making it fit in the enclosure as well as line up with the data and power ports. Also increased the height so that it is about the same height as a 3.5" disk, making...

This adapter allows 2,5'' SATA drives, for example most ssd's to be used more easily in hot swap bay. Requires 2x M3x10 countersunk screws to work NOTE! ...If you are looking for more permanent mount for your ssd inside your case, this one is not for...

Cette version est spécialement destinée à l'adapteur pour disque dur de 2,5" (https://www.thingiverse.com/thing:4831668). ______________________________________________________________________ Replica of the HDD locking system for Synology NAS...

Cette version est spécialement destinée à l'adapteur pour disque dur de 2,5" (https://www.thingiverse.com/thing:4831668). Replica of the HDD locking system for Synology NAS drawer. ...This version is specifically for the 2.5 "hard drive adapter...

HP Proliant compatible 2.5" Caddy Works with G4/G5/G6/G7 ProLiant servers

This is airflow optimized SSD mount in the 3,5" Supermicro drive sleads. This is based the OEM MCP-220-00043-0N mount and works with 7mm thick SSD, let me know i you need a diffrent size. This is made to balance airflow over the spinning rust (HDD)...

A caddy to keep your AOE templates for Warmahordes

This is a 2 to 5 water splitter with tapered push fittings for for soft tubing w/ 3/8" OD, 1/4" ID. Supports are highly recommended. ...This object was made in Tinkercad.

This versatile enclosure fits standard 3.5-inch hard disk drives and can be easily integrated into a wide range of systems, including the Dell FS12-nv7 Storage Server that I successfully utilized.

This is a caddy to use a standard 3.5" floppy drive in the Zenith Z-171 portable computer. This replaces one of the slim 5.25" floppy drives, and can be used to replace both. Note: If you use a 3.5" drive in the Z-171, it will only recognize it as a...

Just screw off the hdd and slap in your go-to ssd, or laptop hdd - you'll need 4x M3x8 screws to do it.

Remix of a solid design creating a channel large enough for 1.75mm clear filament to be inserted for the light pipe. ... Cut the ends of the clear filament as flat and smoothly as possible to maximize light transmission.

Remix to accept a 9mm drive. Category: Computer

The system is now configured to recognize and process 9-millimeter drives, allowing for seamless integration and data transfer capabilities.

Remixed the v3 version to have some chamfers and a more robust plate where you screw in the ssd (had problems printig it with 0,8mm nozzle), also made a slope at the bottom for easier printig. The original by MakinThings:...

The component fits neatly within HP workstation/desktop guide rails, allowing users to continue leveraging the intuitive easy rail system rather than disassembling the case or merely attaching it via the SATA cable.

The second version of my first hdd adapter model for HP computers. ...Allows you to combine with another design: two drives in one bay. ...Compatible with HP Elite 8000 - 8300 tower and small form factor computers.

If you chamfer the tray to case mount holes on print, the screws will self thread in.Pre-screw the case screws into print first before attempting installThe tray is designed to clear massive GPU's . ...The SSD should sit flush with back of drive bay.SSD...

... 4000, 6200, or 6300 sff. ...No screws required. New and improved model 2535v3 is out! It's faster than ever before when it comes to printing. The final version, 2535v5, is the best of all! I'm a big fan of this one. ... Which one do you prefer?

... back at my old designs, and saw an SSD mount I had made. ...I was inspired to go back and make one that works with metric screws (M3x5mm) and that uses much less material. ...I haven't actually printed it yet, so try it and let me know how it goes!

For CoolerMaster and more! ... EASY! No problem, when FDM printing! Optimized size! ...No Supports!

Customized version of https://www.thingiverse.com/thing:3819146 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3819146

... caddy, use PLA. Choose between PLA or ABS for the front panels. Keep in mind that if you're using a 0.3mm nozzle, the front panels won't fit properly and will need to be glued to the base; with a 0.5mm nozzle, they may be too tight to slide easily.

Multi purpose HDD/SSD holder/rack/caddy for r/homelab Can hold 2 x 3.5" HDDs or 7 x 2.5" drives Each of the 7 2.5" slots support both the standard 9.5mm drives and the slim 7mm drives (by aligning to the left/right of the slot), each slot is marked...

These SSD/HDD brackets are designed to fit into the dell OptiPlex 2.5in hard drive bay. Designed around the OptiPlex 3050. Models and fitment may vary. Still working on the fitment but this is useable for those who need it in the mean time. Requires...