delta 36 725t2 3d models
31736 3d models found related to delta 36 725t2.thingiverse
drawers for the fence on the delta 36-725T2 table saw drawer for the right side of the fence is 5" long drawer for the left side of the fence us 4.75" long long drawers are 9.75" printed with 10% because that's what my settings were at. using a...
thingiverse
Delta table saw fence rail drawers for both left and right sides. Wanted the drawers to be longer than the others here to accommodate at least a pencil and not too long that it doesn't fit on my print bed, also rounded corners so they don't hurt...
thingiverse
Replacement throat plate for the Delta Miter 36-235. ...May be compatible with the Delta Miter 36-255 as well.
thingiverse
This is a replacement handle grip for the Biesemeyer fence that comes with a Delta model 36-725 10" Contractor Table saw. The metal pin that the grip fits over has an M6-1.0 thread in the base. ... This thing has a hole in the bottom so you can add the...
thingiverse
This is a zero clearance insert for the Delta 36-725 Table saw. I cut it from 3/4" plywood. It could potentially be 3d printed as well - some minor sanding was required for perfect fit. I did not model a cutout for the shaft housing, so when you...
thingiverse
Saw a YouTube video on stopping dust from falling to the floor using the Delta 36-725 or 36-5000 table saw. Credit goes to Richard Crees and his YouTube channel for designing the wood and sheet metal version of the dust catch that inserts into the...
cults3d
2.5in dust collection accessory for delta table saw blade guard
thingiverse
D_36 - Delta Printer Upgrade Kit This thing is intended to be a one-stop upgrade kit for your Delta printer. As published all parts, with the exception of the Effector, will fit any printer that uses 2020 extrusions in it's construction. The...
thingiverse
This is my first version of my under saw blade dust collection for delta unisaws. It mounts where the old dust shroud normally is, but is designed after the European table saw dust collection. This design allows for you to hook up a 4" flexible dust...
thingiverse
This is a Fence organizer for the Delta 36-725 table saw (it may fit other models also. I designed this to friction fit inside the fence so it is easily remove-able as needed. It the current setup it hold a push stick, glasses, pencils, and small...
thingiverse
A drawer that fits in the hollow square fence tube of a Delta 36-725 table saw. Due to the nature of printing I made the drawer face separately and glued it on with CA glue. This gives a pull tab and a stop so the drawer doesn't go too far in. There...
thingiverse
This part has an ID of 2.5" and snugly fits over the Delta's dust port, which is 2.49". It was printed at 0.15" thickness which was the same thickness as a store-bought adapter. ...The opposite end is 3.9" OD, and my flexible 4" dust collector hose fits...
thingiverse
Model 36-255L (may fit other models) 12” COMPOUND MITER SAW This saw is discontinued and this part can no longer be ordered. Dust collection is not good with this or any miter saw I have used. Without the Dust Shroud, it is virtually non-existent. ...
prusaprinters
Model 36-255L (may fit other models) 12” COMPOUND MITER SAW This saw is discontinued and this part can no longer be ordered. Dust collection is not good with this or any miter saw I have used. ...Without the Dust Shroud, it is virtually...
thingiverse
... version of http://www.thingiverse.com/thing:797104 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=797104 Instructions Using the following options: number_of_pencils = 36 slope_angle = 35 number_test_pencils = 0
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=739573 Instructions Using the following options: font_narrow_widen = -10 font_size = 20 minimal_color_layer_thickness = 0.6 text_thickness = 5 character_spacing = 1 outline_thickness = 3...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=739573 Instructions Using the following options: text_thickness = 4.2 outline_thickness = 3.0 bar_style = bar_only lug_width = 0 border_width = 0 bar_shift = 12 font_size = 32 bar_width = 48.5...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=739573 Instructions Using the following options: outer_margin_width = 1 bar_shift = 0 font_narrow_widen = 0 lug_text_distance = 2 font_size = 12 borderextruder = extruder2 outline_color = Gray...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=739573 Instructions Using the following options: text_thickness = 4.2 minimal_color_layer_thickness = 0.6 bar_length_trim = -32 bar_shift = 30 font_narrow_widen = 7 font_name = Exo lug_length =...
thingiverse
This is a design for a replacement insert for a DELTA 36-220 10-Inch Compound Miter saw. ... Print it with a fairly high infill, no support required, then screw it into the saw and with the saw running slowly lower the blade to cut the groove.
thingiverse
Delta 12" miter saw insert plate for Model 36-255L (might fit others) Uploading two different options. One is smooth on both sides. The other has "indents" on the bottom similar to the original throat insert plate. If you print the one without...
prusaprinters
It works on model 36-075 and possibly others with similar shaped motor.I own this miter saw, and many years ago I broke off the plastic motor cover. I tried gluing it back together but that only held for a few days and it broke off again. I pretty...
thingiverse
As a learning exercise I designed and printed this insert for my Delta miter saw. It fits really well, I only slightly had to drill out the small holes, but otherwise it fits like a glove. I printed this in PLA, 0.2mm layer height, 50% infill. The...
prusaprinters
As a learning exercise I designed and printed this insert for my Delta miter saw. It fits really well, I only slightly had to drill out the small holes, but otherwise it fits like a glove. I printed this in PLA, 0.2mm layer height, 50% infill. The...
thingiverse
I'm brand new to 3D printing and this is the first thing I've ever designed. It wasn't a PERFECT fit but I made it work with some minor modifications. The switch that I used is the POWERTEC 71007 110/220V Paddle Switch, 2.25. I'd encourage...
thingiverse
Fence sliding pad, my used saw was missing these so made a set. ... I recommend printing them with 100% fill and standing on edge with supports so layer lines go all the way through the pins reducing a weak spot at the pin if printed on it's face.
thingiverse
Customized version of http://www.thingiverse.com/thing:560647 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=560647