delta scroll saw 3d models
37711 3d models found related to delta scroll saw.
prusaprinters
This adapter connects a Shop Vac 2.5" hose to the dust funnel on my Delta table saw. There is a screw-on trap for easier removal of long, thin pieces of wood that might fall through the saw. ...There are two screw holes for mounting the adapter to the...
thingiverse
Delta table saw fence rear foot, part number 422-19-048-0001, used on UniRip Fence part number 36-448, has been discontinued by Delta. Print Settings: Printer Brand: RepRap Printer: Prusa i3 Rafts: No Supports: Yes Infill: 50% or more ...
prusaprinters
This tablesaw dial gauge holder is made to fit directly in the slot machined into the table of my Delta saw. The gauge is used to measure the distance from the slot and the blade at front and back to insure the blade is aligned correctly. ...It is a...
thingiverse
Blade Guard replacement for an older Delta Miter Saw. v1 it could be another 0.75 cm wide it does rub on the metal permanent guard. Also the pivoting hole needs to be another 1.0 cm away from the circumference of the overall blade guard, it was just...
thingiverse
... Products before Delta bought them, so it likely fits those as well. Delta also made other versions of the Multiplex RA saw (40-B, 30-A, 20-A, etc.) so this may fit them as well. ...The guard has a 46mm opening about 13mm deep with two set screws.
thingiverse
A drawer that fits in the hollow square fence tube of a Delta 36-725 table saw. Due to the nature of printing I made the drawer face separately and glued it on with CA glue. This gives a pull tab and a stop so the drawer doesn't go too far in. There...
thingiverse
This is a Fence organizer for the Delta 36-725 table saw (it may fit other models also. I designed this to friction fit inside the fence so it is easily remove-able as needed. It the current setup it hold a push stick, glasses, pencils, and small...
thingiverse
Model 36-255L (may fit other models) 12” COMPOUND MITER SAW This saw is discontinued and this part can no longer be ordered. Dust collection is not good with this or any miter saw I have used. Without the Dust Shroud, it is virtually non-existent. ...
thingiverse
This part has an ID of 2.5" and snugly fits over the Delta's dust port, which is 2.49". It was printed at 0.15" thickness which was the same thickness as a store-bought adapter. ...The opposite end is 3.9" OD, and my flexible 4" dust collector hose fits...
thingiverse
I designed this tool for safely feeding small stock into my bandsaw and scroll saw. It works perfectly! ... Print Settings: Printer Brand: LulzBot Printer: TAZ 5 Rafts: None Supports: None Resolution: 0.20mm Infill: 50% Notes: I printed it using M5...
pinshape
I designed this for safe handling of small stock being cut by my bandsaw and scroll saw. It works flawlessly! ... Print Settings Printer Brand: LulzBot Printer: TAZ 5 Rafts: No Supports: No Resolution: 0.20 Infill: 50% Notes: I used M5 Heatset threaded...
thingiverse
I saw in the comments on the original makers upload that everyone had an issue with printing it as it was so I fixed the original file for everyone's use Edited: removed a small piece left on front tab that prevented seating properly
thingiverse
This saw was built back in '88 and has been a faithful companion of mine for over 10 years after my dad handed it down to me. Even then, though, it was already showing signs of wear and tear, but after all these years of frequent use and regrettable...
thingiverse
The end cap of the sliding table telescopic stop of my Bernardo FKS table saw broke, so I designed a new one. Fits just like the old and uses the same screw in the same location, of course. Die Verschlusskappe des Teleskopanschlags meiner Bernardo...
prusaprinters
Model 36-255L (may fit other models) 12” COMPOUND MITER SAW This saw is discontinued and this part can no longer be ordered. Dust collection is not good with this or any miter saw I have used. ...Without the Dust Shroud, it is virtually...
prusaprinters
The end cap of the sliding table telescopic stop of my Bernardo FKS table saw broke, so I designed a new one. Fits just like the old and uses the same screw in the same location, of course.</p> <p>Die Verschlusskappe des Teleskopanschlags meiner...
thingiverse
Schnellspannfutter v4_m4_rtp.stl Für die Verwendung einer M4 Inbus Maschinenschraube und einer M4 Mutter Schnellspannfutter v4_m3_rtp.stl Für die Verwendung einer "normalen" M3 Kreuzschraube und einer M3 Mutter --------------------- The model is...
thingiverse
My dad requested that I create this custom throat plate for his printer, as the original OEM part didn't fit perfectly on the table. This design can be used as a direct replacement if you've lost or damaged your existing one. Update 11/6/19 - I've...
thingiverse
This is a versatile knob that can be secured using a standard 3mm bolt to attach it to any surface, but I chose to use it to tap into place a broken plastic shaft of a potentiometer, and it performed remarkably well, if I do say so myself. ... Check...
thingiverse
Customized version of https://www.thingiverse.com/thing:4614117 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4614117
thingiverse
Needed a replacement after years of use and no longer available for purchase, I believe it is Dremel Part #5296746
thingiverse
Customized version of https://www.thingiverse.com/thing:1246651 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1246651
thingiverse
Throat plate for Delta ShopMaster band saw