developing tank and reel 3d models
2308933 3d models found related to developing tank and reel.cults3d
Developer and fixer saver for Paterson developing tank and it's reel - for 120 films. It saves about 100ml of the developer, fixer, etc. ... Idea taken from: https://www.thingiverse.com/thing:4300849
thingiverse
Developer and fixer saver for Paterson developing tank and it's reel - for 120 films. It saves about 100ml of the developer, fixer, etc. ... Invest in shell (use at least 4 layers/lines) Idea taken from: https://www.thingiverse.com/thing:4300849 ...
thingiverse
I made the tank in Fusion360 and it is fully working. Also remixed the reel to work properly. If the tank is not fully waterproof, use a gluegun to fill the holes. I recommend to print it in PETG or ABS as those last longer. I will probably make a...
thingiverse
The reel is relatively easy to load if you set it on the lower tank and slowly crank the film on, but I recommend practicing in daylight and then in dark with a test role a few times to get the feel of it and recognize when it isn't loading...
thingiverse
This is a spool for developing 16mm film from cameras such as the Minolta 16 series. ...You can load 3 rolls of film per layer, and a standard Paterson tank can accommodate a reel with four layers.
thingiverse
The reel is relatively easy to load if you set it on the lower tank and slowly crank the film on, but I recommend practicing in daylight and then in dark with a test role a few times to get the feel of it and recognize when it isn't loading...
thingiverse
35mm film developing tank. Should print in ABS or maybe PETG. Print with supports touching bed only. ... STEP file and Fusion file attached as well.
thingiverse
It has been tested in a Jobo 1526 tank, but should work in most tanks which can hold at least 3 35mm reels and have a 1" center core. Instructions Print both halves. Thoroughly clean the spiral...
thingiverse
Design for used with the AP or Paterson two-reels developing tank. This is a the 4th version of the wheel, one which I can personally used for my own photography. It takes some practice to load the reel. But it saves a lot of time and you don't...
prusaprinters
I prefer steel tanks, so this is my version.Print 2 each of Plug, Top, outerTube, and Teeth, and 1 centerTube.The parts should press fit together. ... Depending on your printer's calibration, you may need to scale a few of the parts by about...
thingiverse
Developing fluids are poured in through the central hole in the tank lid and out through the spout on the side. The tank includes a pouring spout and clamps to hold the lid on. The lid is secured to the tank with sliding tabs, and a vent allows...
thingiverse
The small JoBo tank is the smallest and least expensive development tank to be used with the 4x5" spindle for cut sheet development and thus often one of the first tools used in your bathroom-darkroom for cut sheet film developing. Unfortunately...
thingiverse
Just increased the height and length of the notch to keep the film tucked in all the way and in place securely while developing.
prusaprinters
Film developing tank, I have designed but yet tested it cuz I don't have access to a printer at the moment. Pieces should screw together, it did not render the screw thread There are 2 versions of the screw cap, one in one piece. ...(dunno how...
thingiverse
Plastimat developing tank column - 2mm thinner, it would fit 4x5 reel for AP tank into Plastimat tank. Good for stand developing or rolling if you have good seals on your Plastimat tank, as the tend to leak. ... Printed from PMfilaments PETG on Ender...
thingiverse
Scaled to fit a Stainless Steel Nikor Developing Tank. Push load type reel. ... Helps to taper film of feed end OTHER SIZES ARE HERE 110/16MM - https://www.thingiverse.com/thing:4831133 MINOX- https://www.thingiverse.com/thing:4831142
thingiverse
Scaled to fit a Stainless Steel Nikor Developing Tank. Push load type reel. ... Helps to taper film of feed end OTHER SIZES ARE HERE MINOX - https://www.thingiverse.com/thing:4831142 17.5MM HIT - https://www.thingiverse.com/thing:4831135
thingiverse
Scaled to fit a Stainless Steel Nikor Developing Tank. Push load type reel. ... Helps to taper film of feed end OTHER SIZES ARE HERE 110/16MM - https://www.thingiverse.com/thing:4831133 17.5MM HIT - https://www.thingiverse.com/thing:4831135
thingiverse
You can easily load sheet in the dark bag and develop it at the daylight. For fixing and washing i recommend to use a small tray, its amazing to watch the fixing process on the light ! ...:D And you can be sure by observing it that it's fixed properly.
thingiverse
This is a fully functional tiny developing tank for developing only a portion (one picture) of an exposed film.
prusaprinters
Scaled to fit a Stainless Steel Nikor Developing Tank. Push load type reel. Helps to taper film of feed end OTHER SIZES ARE HERE 110/16MM - https://www.thingiverse.com/thing:4831133 MINOX- https://www.thingiverse.com/thing:4831142 Print Settings...
prusaprinters
Scaled to fit a Stainless Steel Nikor Developing Tank. Push load type reel. Helps to taper film of feed end OTHER SIZES ARE HERE MINOX - https://www.thingiverse.com/thing:4831142 17.5MM HIT - https://www.thingiverse.com/thing:4831135 Print Settings...
prusaprinters
:D And you can be sure by observing it that it's fixed properly. Print instructionsPrint Settings Printer Brand: Prusa Printer: Prusa Mk1 Rafts: No Supports: Yes Resolution: 0.25 Infill: 100% Filament: Prusa ABS, FLEX black Notes: Use on the built...
thingiverse
This is 3D printed version toy that was originally made from wooden cotton reel, rubber band, piece of candle and stick. You will need printed parts, rubber band and stick. All put together as seen on pictures. Because the 3D print is smooth, you...
thingiverse
The cotton-reel tank/tractor (1966)](https://twitter.com/LBFlyawayhome/status/1540762050552467457), I remembered making these as a kid, so here's my design for one. Support is needed for the hooks on the top of the reel. Otherwise, it's a very...
prusaprinters
The cotton-reel tank/tractor (1966), I remembered making these as a kid, so here's my design for one.Support is needed for the hooks on the top of the reel. Otherwise, it's a very simple print.</p><p>It's clear that, after working with this design...
thingiverse
It seems that these retainers are no longer available, which makes these tanks difficult to use once the clip is gone, even though the tanks are otherwise almost unbreakable and will last for many more years. So I designed this replacement part. I...
thingiverse
So I designed and prototyped this rolling cage that allows me to process roll films in my standard stainless steel Nikor development tank (the size that fits 1 roll of 120 or 2 rolls of 35mm), without losing easy access to the lid. After some...
thingiverse
This is a reel for 35mm film tank developing. Holds 36 exposure rolls for processing in tanks with a 1" center tube. The model includes two ball bearings, one on either side of the reel, to add traction to the film as it is loaded into the reel. Let...
thingiverse
Developing 8 sheets of 4x5 film at a time. Print with PETCF for best performance. ... PLA is too crunchy PLA+/PETG/ABS are too soft ABS-CF should also work.