dewalt table saw 3d models

This is a dewalt table saw rail/track if you want to build a crosscut sled .

The Human has successfully transformed their Dewalt DW745 table saw's throat plate into both a dado insert and a zero-clearance setup, complete with a riving knife for enhanced safety. ...However, they are still fine-tuning the screw height adjustment...

The newer DeWalt Table Saw has no place for keeping small accessories or tools. These allow you to hang things around the saw stand or on the saw tubing on the sides of the saw. There is one that fits the Saw's Tubing and another that fits the...

Extension for the fence adjustment wheel on Dewalt brand table saw (DWE7491). I found that when adjusting the fence for narrow cuts the clamps holding the fence in place scraped against my fingers if I wasnt paying attention. This extensions allows...

These are feet that keep your table saw in place but allow you to easily remove it to take it with you.

Spiral 50mm and 60mm dust hose adapter to Dewalt table saw. ...

Vac Adapter 35mm to 69 mm to fir Dewalt table saw

This is the switch housing for the DW475 Dewalt table saw. I snapped mine off so I took some field measurements and made a new one. ... It is a little different but pretty close to the original.

I'm thrilled to have finally found a coupler that lets me easily hook up my Stinger shop vac to my trusty 10-inch Compact DeWalt table saw. ...After scouring the market, I was starting to lose hope until I stumbled upon this fantastic coupler that made...

This is a DIY project based on bpopp's custom Dewalt table saw dado throat plate design. I've modified the original to accommodate a standard blade, allowing users to create openings that match their specific needs. ...The updated version appears...

With this flappy paddle, I not only increase the stop button surface area of Dewalt table saw, but it allows me to find the On button easier too. And now I can turn off the table saw just by hitting to approx button location with the palm of my hand,...

This adapter was engineered specifically for my DeWalt DWE7480 table saw dust extraction system to seamlessly connect with my ShopVac vacuum cleaner hose. Note: This adapter effectively eliminates dust buildup by fitting snugly over the saw's...

Dewalt Table Saw Miter Gauge Holder This is a bracket to hold the miter gauge on the saw frame when not used. Currently dewalt has no where to hold it, that I can see. The protractor/angle gets set at 10 degrees, and then that guide will sit flush...

I bought a Dewalt 7491 Table Saw last week and I'm absolutely loving every minute of working with it. This is a dado throat plate needed to install or use a dado blade. The dimensions were based loosely on the standard Dewalt throat plate, minus the...

Customized version of https://www.thingiverse.com/thing:5164909 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5164909

Use this design to step down the lower 2.5-inch and upper 1.67-inch vacuum attachments on a DeWalt table saw to the 1.75-inch vacuum hose of a DeWalt shop vac.

An elbow dust extractor for my Dewalt Saw Table dwe7485 Designed on tinkercad : https://www.tinkercad.com/things/8vsQtuC56nz

... DWE7491RS 10-inch table saw and the Bosch TS1004 dust collection bag. ... Dewalt DWE7491RS: https://www.amazon.com/DW7491RS-Table-Saw-Fence-10-Inch/dp/B00002RNWO Bosch TS1004: https://www.amazon.com/Bosch-Porter-Cable-Dust-Collection/dp/B001AS6U9M

I created this adapter for the Dewalt 7491 jobsite saw (table saw). It allows you to use a 2.5 inch vacuum hose on the bottom port of the saw for dust collection. ... The inside of the adapter is tapered for a friction fit.

This part is designed to replace the DeWalt DW745 job site table saw. Printed with PETG at 50% infill and a 25mm shell thickness for added durability, just like my own model. ...If you're also missing the handle nut, it's a standard M6 nut that you'll...

Full credits to: https://www.thingiverse.com/thing:2893293 The t-nut/t-track wasnt the right fit for a Dewalt saw (specifically Dewalt DWE7491-XE) So I made my own to fit. This may well work on other saws which have the follow dimensions for the...

A connector specifically designed to link a DeWalt table saw's vacuum port directly to a standard five-gallon Shop-Vac hose is available on the market.

If you already have an indicator and you want use the jig as is, it is important that the mounting diameter of the indicator is 8 mm and the distance from the center of the spindle to the back is also 8 mm.You need:all printed parts (4 nuts, 1 base,...

Universal dust collector adapter connects Dewalt DWE7491 table saw's 2 1/2 inch port directly to a standard 4 inch vacuum hose, ensuring seamless dust collection operations.

This is a fundamental adapter linking the DeWalt Table Saw (Model: DWE7480) and a 4-gallon shop vacuum. It ensures a snug fit around the dust port at the back of the table saw and the vacuum hose. ... Print Settings Printer Brand: Printrbot Printer:...

An adapter to connect a Dewalt DWE7485 Table Saw (65mmOD) to 2 1/2" (ID) Clear PVC Dust Collection Hose, created in Fusion 360.Both ends have a slight taper.

I designed this Hose adapter to fit my Dewalt table Saw (DWE7491RS) with my Rigid Shop Vac. I have a separate outfeed table which is in the way of me connecting it straight in. So this was the solution I came up with. Supports were only generated...

This is a remix of another t-track rail for a Dewalt table saw, but sized for m6 nuts and bolts instead of m8. I use mine with this great featherboard print: https://www.thingiverse.com/thing:2893293.My last t-track rail eventually broke after about...

Description:  Adapter for the exhaust of the job site dewalt table saw (2.5") to a 40mm vacuum hose.No supports required.Material:  PLAPrinter:  Creality Ender 3 S1Settings:  0.2mm layer heights. Speed at 100. Build plate 60 degC. ...Nozzle temp 200...

This is a remix of two designs to get the best of both for my DeWalt Table saw with metric nuts and bolts. Following Designs are used: Sliding Block: www.thingiverse.com/thing:3973092 The block was dapted to fit for the DeWalt 7491 & 7492 and the...