diatone gt r349 canopy 3d models

For best result, print in TPU without support. Print with top down. Fits Runcam Eagle Pro Micro. 30mm M3 screews are recommended. ... I also recommend route a new top plate, in 2mm carbon (or more).

Diatone R349 R369 Motor Protector For 20xx 22xx motors

Hello, this is my RX antenna mount for the Diatone R349 which comes into the hole an the end of the canopy. You need to drill a bigger hole do insert the antenna thru that hole for the Antenna Mount. It is a press fit, when done with TPU (95a). ...

This bracket is specifically designed to attach LEDs to the Diatone R349. It connects to the rear posts that secure the canopy in place. If the holes are too small, simply drill them out or print at a slightly larger scale of 100.02%. ... The LED...

Shark fin for the Diatone R349 - Helps with turtle mode. Revision 2 is up - Bigger antenna mount for the Lollipop and AXII. ... R3 is up, minor antenna mount delete that should be more accommodating to other types of antennas.

Here's a revision of the text: Shark fin designed specifically for the Diatone R349 enhances turtle mode capabilities significantly. Revision 2 now available - an upgraded antenna mount features on both the Lollipop and AXII models. ... R3 is live,...

Simple GoPro Mountable Canopy design for the Exorcist Frame. Just pick which sleeve you need, print it in TPU or send the file to Brain3D to print for you. The big screw needed for the GoPro sleeve is an M5 and the smaller one is M3. I use NylonX...

These custom brackets were carefully crafted to shield the motor wires of my Diatone R349 drone. They attach securely to each arm with a simple snap-on mechanism. ...I discovered that the arms are slightly wider near the drone's body than they are...

Mounting Armattan's Universal LEDs on the R349 requires a support to replace the stock plastic barrier covering the capacitor. This part is specifically designed for use with Universal LEDs from Armattan, which can be found at RCCrazed.com. ...To print...

Motor Pliers Custom-Fitted Specifically for Diatone's R349 Mamba 1408 Motors.

My receiver was a bit loose, so I needed something to keep it stable and secure within its diatonic range of R349. ...That's why I opted for a simple solution - just take off the canopy and insert the unit into the stand-offs, and that's all set!

Diatone's compact powerhouse, the GT R349, is a remarkable build that has consistently delivered impressive results. It achieves breathtaking speeds and performs acrobatic stunts with ease, rivaling those of its larger 5-inch counterparts. Available...

A super simple way to mount a caddx vista & DJI camera to the diatone rabbit R349; note that the original stack has been replaced with a geprc 20A aio flight controller. This 3d-printed components of this project consist of three-parts: 1) A mating...

This is a dji digital fpv conversion kit for the diatone r349; you'll need to: 1) Replace the default stack with the GEPRC toothpick 20A aio board (https://geprc.com/product/gep-20a-f4-aio/). Note that this board will be elevated so the motor leads...

... small yet effective to get the job done. Link to the VTX Antenna Mount I also made for the R349: https://www.thingiverse.com/thing:3317546 Link to the TBS Crossfire Antenna Mount I also made for the R349: https://www.thingiverse.com/thing:3317512

Since it has zip ties and now a Crossfire antenna holders it hard to level this thing so i just made something small and simple to do the job. Link to the VTX Antenna Mount that I also made for the R349: https://www.thingiverse.com/thing:3317546 Link...

my design for 3inch drone. ...basicaly on r349 hole dimensions. canopy for 12mm lens. vtx akk race 200mw. iflight/diatone 20x20mm stack +alternativ race cage

Diatone GT M3 Spare Upperarm Assembly

Diatone visionary shield

The original Diatone ET160 has a top plate design flaw that prevents most four-inch props from being used unless a longer standoff is employed, which results in the quad becoming too tall and aesthetically unpleasing. To address this issue, I...

... the standard one if you manufacture it in ABS. ... You can also repurpose brass inserts from a discarded canopy or purchase M2X3.5X3MM components. ... Infill settings - 100% Two designs are available, featuring either antenna openings or none at all.

... for the arm ends, which can also be mounted under the motors for added "soft mounting" support. In addition to these parts, I'm using the Diatone GT-R90 Receiver Shelf, available on Thingiverse as this project. ... Thanks for taking a look!

So I was out flying with my GT-R90 drone from Diatone when suddenly I experienced an extremely severe crash that ended in a catastrophic failure of the frame. I just couldn't wait to get a replacement frame sent, so I decided to design one myself...

Rapid Mount Solution for Diatone R349 and Realacc UXII Stubby VTX Antenna. Intended to Attach Over Top of Quad's Canopy Mount, Not Directly to Stand-Offs. Snug Fit Ensures Minimal Exposed Antenna, Which May Impact Signal Strength. ...Need Further...

This is a Remix of the 3D printable Arm for the Diatone GTM3 (2018) Model. ...I made it a little bit thicker as the OV.

Diatone's little 3 inch monster the GT R349 is an amazing craft and has a proven track record. It achieves astonishing speeds and all the acrobatics of a 5 inch. With the Caddx Nebula v2 coming out, it was time to convert my favorite 3 inch to the...

Mounts for the bn180 GPS module are designed specifically for the diatone r349 rabbit 3" quadcopter. I've only tested the vertical mount, as it keeps the GPS closer to the frame and provides better protection. ...A horizontal mount was created in case...

I'm using a mount specifically designed for the BN180 GPS and Foxeer Lollipop antenna on my Diatone Rabbit r349 drone. The BN180 is positioned horizontally, which isn't perfect but appears to function well enough for me. ...Make sure you point the BN180...

This is a BN-180 GPS Sensor mount that fits my Diatone R349 HD MK2. It holds the GPS very securely. I was able to zip tie my receiver (R9 MM) to the bottom of it, as well. Which is really nice to free up some space. I have not checked to see if...

This is a BN-180 GPS Sensor mount that fits my Diatone R349 HD MK2. It holds the GPS very securely. I was able to zip tie my receiver (R9 MM) to the bottom of it, as well. Which is really nice to free up some space. I have not checked to see if that...