diatone gt r349 3d models
10799 3d models found related to diatone gt r349.thingiverse
Diatone GT-R349 and similar battery protector\launchpad. In comparison to the thing it is remixed from (https://www.thingiverse.com/thing:2588938) it weights approximately nothing - 8 grams. Needs to be printed with supports. ... Fusion360 archive...
thingiverse
Clean plate for diatone gt r349, compatible with umma85 and 95x parts.
thingiverse
This is a canopy for the Diatone GT-R349, longer on the front to avoid the propellers in the visual field. ...It can be printed both in TPU or PLA.
thingiverse
Original post_ Made this mount some time ago for my Diatone GT R349 micro drone. It's far enough from the bottom mounted battery and it doesn't touch the frame. Range for this kind of quad isn't an issue I think. Never had problems. Printed...
thingiverse
Used in Diatone GT R349 to hold battery wires, capacitor and antennas Check more details from this build at https://rotorbuilds.com/build/22688
cults3d
Used in Diatone GT R349 to hold battery wires, capacitor and antennas Check more details from this build at https://rotorbuilds.com/build/22688
cults3d
This is the R349 Lollipop mount remixed for the Lumenier Micro AXII. ...Many thanks to KTMDirtface for the original and for including the f3d and step design files.
thingiverse
This is the R349 Lollipop mount remixed for the Lumenier Micro AXII. ...Many thanks to KTMDirtface for the original and for including the f3d and step design files.
thingiverse
... I never fly without a Battery powered Buzzer. It have save my life often. This version accomodate a FullSpeed Lucky Box Beeper/Buzzer and a TBS Nano rx On a Diatone GT-R349 and GT-R369. ... Cannot confirm on compatibility with GT-R249
cults3d
... greatly. This is an Insta360 Go Camera mount for the Diatone GT R349 & R369. The camera angle can be varied. ...According to my testing, the Jello in the Insta360 Go's video is way less in this orientation as compared to the horizontal orientation.
thingiverse
Remixed an existing reciever mount to be just the antenna themselves. ...I'm using an FRSky XM+ tucked under the flight controller board and the antenna ran out the back.
thingiverse
This TPU part allow you to install and protect bigger camera like the Ratel on the GT-R349 (should work on R369 and R249). The original canopy have too short camera protectors and if you install a Ratel, the lens become vulnerable. After few...
thingiverse
on about my 4th flight I bounced off some tree limbs I didn't see and landed in the street scuffing up one of my arms.. decided that an arm protector would be worth doing, so came up with this using fusion 360. it will provide soft mounting and arm...
thingiverse
I printed mine at 0.7 layer height, i have a 0.8 nozzle, no supports and 0% infill, my walls are about 0.8mm. ...my frame (not ducts) are solid, because my top/bottom layers are thick, if you print with a 0.4mm nozzle, use simplify 3d to print the frame...
thingiverse
Simple, but sturdy antenna mount for the back of your drone. To install, remove the two metal posts at the rear of the frame, insert them into the mount, attach your antenna adapter and re-install them onto the drone. I do not remember what the...
thingiverse
Printed in TPU, this is a real quick design probably not the best I have not flown with it yet. ...
cults3d
This is an Insta360 Go Camera mount for the Diatone GT R349 & R369. The camera angle can be varied and detached from the quad when not flying. The camera mount provides protection to the camera lens. ...I wasn't able to find such a design on the...
thingiverse
##Canopy Diatone R249/R249+/R349/ER349/R369 You'll need: - 4x screws M2 (between 8mm and 10mm) - 2x screw nuts M2 - 2x screws M2 for micro camera - 2x standoffs M2 19mm - original (or 20mm) - 1x 3" frame compatible (GT R249/R249+/R349/ER349/R369)...
cults3d
##Canopy Diatone R249/R249+/R349/ER349/R369 You'll need: 4x screws M2 (between 8mm and 10mm) 2x screw nuts M2 2x screws M2 for micro camera 2x standoffs M2 19mm - original (or 20mm) 1x 3" frame compatible (GT R249/R249+/R349/ER349/R369) Frame R349: -...
thingiverse
I wanted a way to throw my Diatone GT R349 in my bag without damaging it or taking up too much room. It's about 10mm larger than the quad in all 3 axes. Uses pick and pluck foam (95x15x15) to hold it in place. Snap fit lid. The tolerances are...
thingiverse
Duct for R349, only need to remove the props to install. ... Screws not needed, can be installed with a ziptie.
thingiverse
Diatone R349 R369 Motor Protector For 20xx 22xx motors
cults3d
Shark fin for the Diatone R349 - Helps with turtle mode. Revision 2 is up - Bigger antenna mount for the Lollipop and AXII. ... R3 is up, minor antenna mount delete that should be more accommodating to other types of antennas.
thingiverse
Shark fin for the Diatone R349 - Helps with turtle mode. Revision 2 is up - Bigger antenna mount for the Lollipop and AXII. ... R3 is up, minor antenna mount delete that should be more accommodating to other types of antennas.
thingiverse
I designed these brackets that cover the motor wires on the Diatone R349. They just snap on to each arm. FYI, the arms are a bit wider near the body, as opposed to near the motor. It's easier to snap them on closer to the motor, and the slide them...
thingiverse
A simple bracket to mount LEDs to for a Diatone R349. The bracket connects to the two rear posts that hold the canopy on. If the holes are too tight, just drill out or print at 100.02%. ... The LEDs I purchased are these: ...
thingiverse
Hello, this is my RX antenna mount for the Diatone R349 which comes into the hole an the end of the canopy. You need to drill a bigger hole do insert the antenna thru that hole for the Antenna Mount. It is a press fit, when done with TPU (95a). ...
thingiverse
A support for mounting [Armattan's Universal LEDs](https://www.rccrazed.com/accessories-leds-armattan-universal-led-p-313.html) on the R349. It replaces the stock plastic barrier that covers the capacitor. ... Must be printed in TPU: insert the LEDs...