direct mount chain guide 3d models

Standar 2020 aluminum profile filament guide. ...Print Settings Rafts: No Supports: Yes Resolution: 0.24 Infill: 15% Post-Printing Category: 3D Printing

I got tired of my filament snapping on long drives to outside corners, so I wrapped it in wasted Capricorn Bowden tube I lost with a Direct Drive upgrade from Printermods.com. You'll need two male straight pneumatic PTFE Tube Push in Quick Fitting...

Hotend Mount for Chain Cable - Ender 5 Plus

I reduced the width of the original design to avoid hitting the X carriage when moving in the Y direction. This will fit an Ender 5 with a direct extruder. Category: 3D Printer Parts

I needed a way to route filament over the top of my kobra max due to converting to direct drive.

For the Ender 5's filament feeder, follow these steps when using a direct drive system. ...Ensure that all standard screws and nuts from the extruder are utilized.

This is just the bottom part of the extruder carriage bracket (below the slight setback under the chain shelf), if you want to check your slicer settings against the spacing of the wheel sleeves and the two mounting bolts. It is much less PLA than...

Update 10/11/2019 I realized the filament guide I originally designed is garbage if you are printing tall prints. I designed a new one and it is here and pictured. You may need to ream out the hole for the Capricorn Tube, depending on your printer...

Routing Wires with Ease: A Step-by-Step Guide. To avoid wire tangles, follow these straightforward steps: 1. Extend the Extruder Motor Cables by 50cm. - Either add an extension or replace the wires entirely to ensure they reach from one end of...

On June 30, 2020, I revised the design by adding a small tube; you can view the updated STL file, Filament Guide Rev3, along with its associated image. ...Feel free to print, remix, or add comments; I'd appreciate seeing pictures of your prints as well.

My direct drive ender 3's just allows the filament to glide back and forth on the top rail. ... Seeing the original remix work fine of my CR10's I did a quick remix to use the same setup on my enders without the filament sensors.

I use a direct drive hot end and found that I needed to keep the filament ‘high up’ and inside the print volume, I’d been using a piece of twisted wire for months no finally got around to designing something for the purpose.Added a v2 that is rounded...

Printing it now, but this setup is primarily designed for direct drive extruders with the spool positioned directly above them. I created this arrangement to maintain a slight tension on the filament line, allowing the spool to slide smoothly while...

This may be really specific to my direct drive setup on my Ender 5 but I find it useful, so I'm posting in in case anyone else can use it. I use this in conjunction with https://www.thingiverse.com/thing:3628876 by Daede to lift my Bowden tube up a...

This may be really specific to my direct drive setup on my Ender 5 but I find it useful, so I'm posting in in case anyone else can use it. I use this in conjunction with https://www.thingiverse.com/thing:3628876 by Daede to lift my Bowden tube up...

I loved the design of the bearing roller but needed it to mount to the top of the printer. ...You will have to unscrew the top rail to slide this on (despite the file name, it is not a snap-in.)

Could not find a filament sensor setup for a direct drive, so here it is! This works well and no filament breakage so far. Note: There are two balls I use the smaller one, so it moves freely with the filament. I sanded it and used dielectric...

Ever since I upgraded from a bowden to direct drive extruder on my Ender 3 Pro, I was not satisfied with the cable management above the X-Axis (i.e. E-Stepper Drive, BLTouch, Fan, Thermistor Cable etc).\r\n\r\nI therefore designed a cable organizer...

Thank you to [tomaskom_cz](https://www.thingiverse.com/tomaskom_cz/) for the [roller design](https://www.thingiverse.com/thing:3095575) Thank you to [Evan_vw](https://www.thingiverse.com/evan_vw/) for the [2020 rail...

Stick on drag chain guides for the Shapeoko CNC. I used 3M panel tape to stick them to the rails. ... There is a recess on the appropriate side to accept the panel tape and still ensure a flush mount.

Remix of [Ender 3 Cable Chain Extruder Mount](https://www.thingiverse.com/thing:4592642) for [Ender 3 Cable Chain, no screws, no unplug cable](https://www.thingiverse.com/thing:3769941). It's going to need supports, but you can decide which direction...

This design enhances filament steering towards a straightforward extruder. It can be easily installed onto a V-Slot frame. ...Additionally, a Fusion 360 model is provided so users can personalize it to suit their needs.

... testing out the junction part were the two cable trays attach to the factory extruder location. (direct drive sits on top making the chain part higher and the mounting points don't line up) Made up some spacers to get the right height. ...

A top-notch roller sleeve for your chain damper is what you get - seamless installation and a perfect fit every time, no matter the size.

Bike chain guide for superior xp 939, required 3 bolts M 5 , 1 nut M5

Adaptable wear part for low chain guides type XLC, printed in PLA or TPU98

if you have a v1 druid or dreadnought and have upgraded to the race guide only to have it detonate on you like me... here you go.I printed this outta PC-CF and it worked great. I print it vertically and it worked well, will need support either way.

- This is a chain ring guide for bicycles - You can customize it to your liking using the customizer. ... - Designed to be easy to print - no supports needed **2021-10-02** - Added option for zip-tie mounting - Fyi - printed and tested and it works like...

I recommend to use some tape under chain guide for secure mount and seat tube protection.I created this model because i was not able to find the right spacing of the groove for the chain.Please write comment if you need different spacing. ...Also...

I'm planning to utilize my X chain following a swap to connect directly to e3d. So, I'll create a custom chain holder. It's really straightforward. The longer length fits perfectly with my setup. If someone prefers a shorter chain, they can have...