diy dual monitor stand 3d models
221081 3d models found related to diy dual monitor stand.thingiverse
Inspired by https://www.thingiverse.com/thing:4656621 Honeycomb shape monitor stand. ... 3 identical parts are printed and attached to a piece of wood to support monitor.
thingiverse
I made myself a mobile monitor (12v supply for the ability to be used with a battery) for my MacBook because I like working with two monitors. Video editing etc. The stand is easy to print, even without supports. It took me around 4h to print with...
thingiverse
This is a model for fixing the notebook panel diy to the windowsill. Please pay attention to play. ...I recommend putting a stick in the middle to strengthen.
prusaprinters
Both of the legs can be printed at the same time on my 230 x 230 mm bed.It's designed to raise your monitor by 80mm and fits board that are 150mm wide and 15mm thicc. I personnaly used a 500mm long board but you can use whatever lenght you...
grabcad
No credits on this one. ...I downloaded most of the parts from here, and the original idea is from Herman Miller's system. I just needed a dual monitor stand fast. ...I did make the monitors
grabcad
... As you can see on renderings, some fasteners are missing. You can use your own. Dual Monitor Stand can be recreated using steel laser cutting, welding and press folding. ...It has not been made yet, but I'm going to make it to use on my workspace.
cults3d
Modular dual monitor stand based on metallic tubes OD 25mm with vesa75/100 mount Recommended length of tubes: 2x500mm vertical 2x300mm legs 4x700mm horizontal (or 800mm for monitors more than 23") Length can vary, depends upon monitors you have.
thingiverse
Modular dual monitor stand based on metallic tubes OD 25mm with vesa75/100 mount Recommended length of tubes: 2x500mm vertical 2x300mm legs 4x700mm horizontal (or 800mm for monitors more than 23") Length can vary, depends upon monitors you have. ...
myminifactory
adjustable dual monitor stand requiring use of hose clamps, and some self tapping screws. Parts needed: 8 or 10ft of 3/4" EMT conduit 6-8 hose clamps about 10- #10 x 3/4'' self tapping screwsPrinted parts: 1 EMT monitor base 1 vertical cap 2 vesa...
thingiverse
You could technically configure these parts to make a huge array of monitors, and you can use the spare space on the leg to attach other devices (like webcams, lights, speakers etc.) As always with my designs. Use at your own risk. I am not...
thingiverse
Hope you like this monitor stand. Its intended for two Dell U2312HM on top of each other. Others may work as well since the stand uses the standard VESA Mount which is found on almost all flat screens. The angle of the monitors can be adjusted. :-)...
prusaprinters
Simple solution for storing sd and micro sd cards with magnet slot to keep notes at sight and 2 usb drive holes on top. Designed for stand pipe diameter of 35mmMagnet size 12x8mm
thingiverse
This project was inspired by those cool IKEA shelf to monitor stand hacks I've seen floating around, though this one is designed for us Aussies. It was cheap to make, super easy to print and I think it'll look great on any modern desk with its clean...
cults3d
This project was inspired by those cool IKEA shelf to monitor stand hacks I've seen floating around, though this one is designed for us Aussies. It was cheap to make, super easy to print and I think it'll look great on any modern desk with its clean...
prusaprinters
Discovered my ergonomic posture was suffering and I needed my screens higher, but the Wali stand was already adjusted at the maximum height.I printed these having a small height adjustment makes a huge difference for my posture.Design is somewhat...
cults3d
Side support for Monitor Stand DIY Measures of the hole for wood 140mm x 12mm Two screews to fix the table on the side support on both sides. You have 2 different stls. ...So you can print it on different colors that you like more.
thingiverse
An Adapter to use an articulated lamp on my dual monitor stand.
thingiverse
Microphone Holder for Dual Monitor Stand use M4x30mm bolt with wing nut designed for 36mm post
thingiverse
... match the size of your phone. ...I used hex bolts with wingnuts to connect each part. The diam of the clamp that fits around the pole mount is 1.34" The dual monitor stand is: Planarhttp://www.planar.com/products/accessories/desktop/dual-monitor-stand/
thingiverse
Simple pipe end plug to mount a microphone boom on the top of a dual monitor stand. It should work will all tubes that are 1 3/8 in diameter and nearly all table clamp boom arms on Amazon. You will need to deburr the tube before pushing this in. A...
thingiverse
This is a dual 24" monitor stand I have designed to be 3D printable.****Use this at your own risk***. If you don't understand basic structural design concepts and are a beginner at 3D printing I do not suggest you attempt this project. I am not...
thingiverse
I wanted a way to mount my laptop on my existing monitor stand so that the screens would be at the same working height. This required lowering one of the arms, but they were attached by a shared bracket. This was my solution. ...I don't know the brand...
pinshape
Summary This is a dual screen monitor mount that can be made for around 15 euro. The only things that have to be bought are some nuts and bolts and the aluminium tubing. The rest can be printed. Later I added a support in the middle between the...
thingiverse
This is a dual screen monitor mount that can be made for around 15 euro. The only things that have to be bought are some nuts and bolts and the aluminium tubing. The rest can be printed. Later I added a support in the middle between the screens...
thingiverse
A couple parts are from other user & some parts have been customized for Anycubic Chiron Printer
thingiverse
... for the Logitech C270 webcam. ... My specific stand is the WALI Free Standing Dual monitor stand from Amazon https://www.amazon.com/gp/product/B018MU3SAS/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1 However, it should fit any stand with a ~35mm pipe
pinshape
To main monitor ASSEMBLY MANUAL: http://www.artics.it/stv-is-it/progetti3d/manual/dual-lcd-stand-steps.pdf Glue is NOT necessary. Use a 2-3 mm Allen wrench to fix the inclination of the support of each monitor. Print the long parts horizontally for...
cults3d
Drawer: https://cults3d.com/en/3d-model/various/monitor-stand-drawer-vajon-para-soporte-del-monitor It has a honeycomb design that gives it a lot of strength being able to withstand any type of monitor Hope you enjoy it!!! Any comments and if you...
thingiverse
I liked my new wide monitor shelf, but the legs were far too tall (4"). I needed legs that were just high enough that I could slide my keyboard under, but not too tall that I had to look up to see the top of my screen. I used books to figure out the...