diy quadcopter 3d models

My capstone submission for the Manufacturing Process with Autodesk Fusion 360 Course

This frame is made to fit 11-ish mm square aluminium tubes which you can cut to size to make a quadcopter of any size. ... Recommend printing with support on the inside of the arms.

This frame is made to fit 11-ish mm square aluminium tubes which you can cut to size to make a quadcopter of any size. ... Recommend printing with support on the inside of the arms.

This frame is made to fit 11-ish mm square aluminium tubes which you can cut to size to make a quadcopter of any size. ... Recommend printing with support on the inside of the arms.

A simple Quadcopter frame designed for a school project. We planned to 3D print everything, but due to a lack of time we had to resort to a laser cutter for most parts. Obj's are 3D printed, svg's are lasercut from 4mm plywood. Arm heads designed...

Задумка была на интерес, но рама оказалась вполне приемлемой и главное ремонтопригодной, по весу около 125 грамм. Квад на удивление не плохо полетел и показал- время висения 26мин., ток висения около 8А. скорость до 80км/ч, скороподъемность до 8м/с...

In this thread i will adding the 3D printable improvements that go specifically designed for this model all ready Done:Power PCB Support Future improvements: Led light for Tail / Nose, Camera Supports ,GPS Supports, Battery holder This RoboCat 270...

Got from the Open Pilot forums Open Frame Parts from grabcad.com : Tiger MT2814 GoPro Hero 3 HD Camera with the Frame 9x4.7 Propeller credit to: jbkappirossi for more info about the model http://forums.openpilot.org/topic/12600-open-frames/ Note:...

... pretty happy with results. More about this project you can find on this page where I made description for each step: http://www.instructables.com/id/DIY-quadcopter-joystick-and-frame/ In zip file are included .stl files and Solidworks 2015 files,

... a screwdriver to tighten Complete assembly Tie up all the lines. Crazyflie flight control Very larger Propeller Special apron Ok, this is my DIY quadcopter, what about it ?

I wanted to take the thought out of a fun first DIY build. I've wasted too much time and money trying to figure out the right components and so hopefully this is a setup that will work well for you. I'm also working on a easy to follow instruction...

I wanted to take the thought out of a fun first DIY build. I've wasted too much time and money trying to figure out the right components and so hopefully this is a setup that will work well for you. I'm also working on a easy to follow instruction...

SENBAN is Japanese for a rotating machine and this term fits perfectly to a Quadcopter. The AP SENBAN has the look of a Yayuji throwing star as it was used in some Ninja movies by the famous Sho Kosugi. My PETG printed frame with 50% infill...

This is a new version of my original design here: http://www.thingiverse.com/thing:128535 This was designed with Rhino 3D and printed on my MakerBot Replicator 2. The differences in this design are the following: Less parts to print. This...

This is a new version of my original design here: http://www.thingiverse.com/thing:128535 This was designed with Rhino 3D and printed on my MakerBot Replicator 2. The differences in this design are the following: Less parts to print. This...

Updated version. Reworked space. Gps transfered to the battery door. Camera and gimbal changed. ... All printed v1 frame can use only changed parts.

Got from the Open Pilot forums Open FrameParts from grabcad.com : Tiger MT2814 GoPro Hero 3 HD Camera with the Frame 9x4.7 Propellercredit to: jbkappirossi for more info about the model http://forums.openpilot.org/topic/12600-open-frames/Note: Bad...

The files include a parameterizable OpenSCAD source file which allows to define the desired tube diameter as well as most of the other sizes. The two STL files are examples showing a small version designed for 2mm screws to connect the top-plate and...

This mini quad is a work in progress and you can check out the build log here: http://garagepilots.com/page/diy-mini-quadcopter-w-3d-printed-frame and the garage maiden flight here: http://www.youtube.com/watch?v=sNW7EB0OWqE and here is a build log...

This mini quad is a work in progress and you can check out the build log here: http://garagepilots.com/page/diy-mini-quadcopter-w-3d-printed-frame and the garage maiden flight here: http://www.youtube.com/watch?v=sNW7EB0OWqE and here is a build log...

Quadcopter, self-modeling printing, test flight，Brush program Multiwii，use 716 Coreless motor

Features 3D printable Designed for 3S 5000 mhA battery with 160 x 56 x 35 mm capacity Created for CC3D controler GoPro mount with vibration avoider Source files Available on my Github : https://github.com/seblaporte/quadcopter_T450 Video First...

STL and Solidworks 2018 files for DIY ESP32 quadcopter project https://github.com/RomanLut/Multiwii-ESP32-port http://www.youtube.com/watch?v=lwrkspHjSu4

DIY quadcopter (like F250-300) 18/10/2015 : V2.0 (Arms modified) Print Settings Rafts: No Supports: Doesn't Matter Infill: 80% Notes: 80% to 100% infill 0.2mm layer 30mm/s speed PLA 205°C

Quadcopter - X450 carbon fiber frame - 10in blade - Pixhawk flight controller - Turningy ESC - Multistar high capacity 4000mAh battery - NTM Prop Drive 800Kv motors Disclaimer: The CAD file for frame is from Alex Baval

... the same as the original on http://www.thingiverse.com/thing:1541511. Print Settings Printer Brand: RepRap Printer: Rebel II Rafts: Doesn't Matter Supports: No Resolution: 0,2 mm Infill: 30% Notes: I used for all items of quadcopter material PETG.

ALSO AS SOON AS WE REACH FIVE HUNDRED DOWNLOADS THIS DIY QUATCOPTER WILL BE DISCONTINUED. DO TO THE NEWER AND BETTER UPCOMING FRAMES. BY JUST DOWNLOADING THIS FRAME ALONE MAKES YOU A UNIQUE INDIVIDUAL. JOIN US ON FACEBOOK AND WATCH IT GLOW :...

DIY Drone

Print build and fly....individual component files are available.

Based on Firefly Pro, I modified some parts to make it more stronger and easy to change part in case of crash. Total weight with electronics elements : 565g I use 1500 mAh battery for approximately a 7-8 minutes flight. ...First flight :...