dji mini range extender 3d models
170907 3d models found related to dji mini range extender.prusaprinters
<p>Simple parabolic signal booster. Stick any aluminum foil inside.</p> <h3>Print instructions</h3><p>Print it with a 5mm brim, left or right side down. ...You need two pieces.</p>
thingiverse
Quick Remix of Coryt1979s Mavic Mini Antenna for 5.8Ghz band. This one is designed for 2.4 GHz and also uses 3mm directors. ... Frequency : 2450 MHz Wavelength : 122 mm Rod Diameter : 3 mm Boom Diameter : 4 mm Gain : ...
thingiverse
So I just received a DJI Mavic Mini drone, and before using it, It was so hipped that I watched a lot of video on the web about it. I saw that the CE version has less range than the FCC one since the max power limit emitted was lower. And so,...
thingiverse
This is a remix originally made by rosscadguy This design it to allow you to fit the YAGI range extenders and then this mount will fit over them to hold the IPAD mini in place
thingiverse
DJI Range Extender Plus. ... I used with my DJI Spark, but can be used with Mavic PRO and others. Paste aluminum foil into reflector. In my tests, my DJI Spark maximum range without this extender was 600m, and with this extender was 1200m.
thingiverse
This device has to be put on your Spark's remote control and then will extend it's range. ... In order to work you have to stick some copper tape (or aluminium foil) inside the shells.
thingiverse
This print is designed to extend the range of the Spark remote. ...Insert a 0.5-1mm aluminum foil.
thingiverse
This is a supportless 5.8GHz parabolic reflector antenna for my DJI Phantom 3 transmitter Initial testing got me way past the old weak signal or loss of signal spot on my range any kind of foil / foil tape will work, I used Shurtape AF 912 Foil Tape...
thingiverse
Petite boite pour ranger deux batteries DJI mini 2. Peut certainement être amélioré, mais pour moi, c'est ce que je chercher. Bonne impression. ...
thingiverse
It is a range extender and I have three files. One for 3mm, 3.25, and 3.5mm soft iron rod. Just cud any soft iron, coat-hanger works well, 10 pieces at 12 to 15mm length, and 2 at 25mm for the lowest rung of the extender. Fits like a glove and...
myminifactory
This easy-to-print Range Extender will extend the range of your DJI Phantom 3 or DJI Inspire 1 considerably. It slips easily onto the standard un-modified DJI Controller Antennas and can be quickly installed or removed with one hand – even when your...
cults3d
I’ve tested this DJI Phantom 3 / Inspire 1 Range Extender with my Phantom 3 Pro, and it works very well, delivering substantially more maximum effective range. Please note that no antenna range extender works well through heavy cover (such as...
thingiverse
I’ve tested this DJI Phantom 3 / Inspire 1 Range Extender with my Phantom 3 Pro, and it works very well, delivering substantially more maximum effective range. Please note that no antenna range extender works well through heavy cover (such as...
cults3d
I’ve tested this DJI Phantom 3 / Inspire 1 Range Extender with my Phantom 3 Pro, and it works very well, delivering considerably more maximum effective range. Please note that no antenna range extender works well through heavy cover (such as...
thingiverse
Range extension antenna for dji Mavic Mini drone. 2.4 Ghz frequency (use manual adjustment in RC). Based on my tests, it increases the range to at least double the edge of a populated area. Keep heading! Use a copper or aluminum rod (3mm). Your...
thingiverse
This is my remix of the 2.4ghz range extender with slightly larger holes for the rods. I found the plastic was under tension and cracked easily. ...This design will be loose on the rods so a drop of superglue will be needed to stop it falling out.
thingiverse
Able to attach a strap to the controller while also accommodating the new mount used with the alientech range extenders. Fits into the void where the cables go along with clips on behind the controller. Solid infill along with a a small brim helps...
thingiverse
... ...The last element (reflector) could also be much bigger. Its for Mavic Mini CE version (Europe), so I focused on 2.4 Ghz, which gives by default the maximum distance. ...I will be happy if someone tests it and write the results in comments!!
cults3d
... ...The last element (reflector) could also be much bigger. Its for Mavic Mini CE version (Europe), so I focused on 2.4 Ghz, which gives by default the maximum distance. ...I will be happy if someone tests it and write the results in comments!!
thingiverse
Its for Mavic Mini FCC version (US), on 5.8 Ghz, - maximum distance. I will be happy if someone tests it and write the results in comments, I am in EU but made the model based on https://www.thingiverse.com/thing:4457347, after some requests!! ...Tip...
cults3d
Its for Mavic Mini FCC version (US), on 5.8 Ghz, - maximum distance. I will be happy if someone tests it and write the results in comments, I am in EU but made the model based on https://www.thingiverse.com/thing:4457347, after some requests!! ...Tip...
thingiverse
This adapter attaches a Yagi,Uda antenna to the Hubsan Zino Mini Pro/SE controller. 2.4GHz only. 2.4GHz_scale.stl Scale for cutting metal rods with a diameter of 3mm. 60mm, 49mm, 48mm grooves were made. It is good to cut about 1mm longer and file...
prusaprinters
Range extender for DJI Mavic drones. Designed for the Mavic Mini controller but I believe most DJI drones have the same antenna design so it should work on most. I used reflective foil tape as a backing. The antenna grip must be printed using...
thingiverse
Range extender for DJI Mavic drones. Designed for the Mavic Mini controller but I believe most DJI drones have the same antenna design so it should work on most. I used reflective foil tape as a backing. The antenna grip must be printed using...
thingiverse
Made a simple foldable range extender for the Dji Mavic PRO, without any silly nametags as everyone else only the best name, Dji Mavic PRO ;)! Fits the spark controller aswell, even though it says DJI mavic PRO hehe. I used aluminium tape that is...
thingiverse
... by using his file to create a new sketch and extrude a whole new object out of it. I had no problems slicing this new file and printing it. Recreated Antenna_Grip.stl and made it slightly smaller on the outside to better fit into the extender.
thingiverse
Summary hi i made this just looking at my ce mavic mini Eu ((((((((((over 4000m long range)))))) https://www.youtube.com/watch?v=rrYm9NoZdk4 remix from and thanks form the files https://www.thingiverse.com/thing:2788073...
thingiverse
The step up will change the USB voltage from 5v to 12v (default voltage of the power supply but range is 6-12v according to the datasheet). Power consumption from the USB socket is around 0.6Ah at 5v. - You need to open the booster to desolder the...
prusaprinters
The step up will change the USB voltage from 5v to 12v (default voltage of the power supply but range is 6-12v according to the datasheet). Power consumption from the USB socket is around 0.6Ah at 5v.</li> <li>You need to open the booster to desolder...