dji phantom 2 ipad 3d models

I have made 2 designs for iPad mini that attaches with the Apple Smart Cover or Case and another one without cover or case. ... I printed on Da Vinci 1.0A with the following setting : Layer height : 0.2 3D Density : 0.15 Shells : Standard Any suggestion...

This will allow you to use an aired (even with cover and protective back) with the Phantom 2 controller using the stock included iPhone clip. ...No mods needed.

just make it a bit fat, correct some aberrations, remesh and add dji logo,also its necesary to fit some slide cotton stripes to secure the ipad on the mount,now works really fine, hope everybody enjoy it.

It's a iPad 2 3 4 holder for Phantom Dji Standard. ...And it already has support Just print in 0.3, and cut out all the support

SummaryIt's a iPad 2 3 4 holder for Phantom Dji Standard. ...And it already has support Just print in 0.3, and cut out all the support

Just install Your iPad Mini onto the included Smartphone Holder which comes with the Phantom 2 Vision Series Quadcopters. ...Beware of the Power Switch and install the iPad Mini correctly or it will be pressed continously!

3 Parts: Mount for the Clamp, Top Holder where the Off-Switch resides and the Bottom Holder. ...Mount them correctly or it will always press the Power Switch!

Revised the Ipad holder vertical mount so that it can be used with a Range Extender https://www.thingiverse.com/thing:1096728 on the DJI Phantom 3 Standard with the single antenna. I also slightly re-shaped the mount where it contacts the transmitter...

Revised the Ipad holder vertical mount so that it can be used with a Range Extender https://www.thingiverse.com/thing:1096728 on the DJI Phantom 3 Standard with the single antenna. I also slightly re-shaped the mount where it contacts the transmitter...

made this bracket to fit my ipad mini which is in a lifeproof case too fit on the Dji phantom hand set. ... https://youtu.be/M6zYJAGwwIY

Hello! ... This is a small temporary small extender to use your dji phantom 3 standard with an ipad mini. ...It works well and you don't need support,infill and you print it at 0,2mm Hope you enjoy

http://www.thingiverse.com/apps/customizer/run?thing_id=384919 Instructions Using the following options: interiorLength = 300.0 lidInsetHeight = 15.0 hingeThickness = 0.0 lidInsetOffset = 0.0 coverThickness = 2.0 interiorHeight = 200.0 rimInset = 1.0...

http://www.thingiverse.com/apps/customizer/run?thing_id=384919 Instructions Using the following options: coverThickness = 2.0 hingeFillet = 00 interiorFillet = 5.0 hingeThickness = 0.0 hingeWidth = 00 hingeLengthScale = 1.1 rimInset = 1.0...

The iPad Mini (all versions are the same size) slides into the visor and the whole thing is then clamped onto the DJI RC unit. The idea for this design was to make it light weight, so the walls of the visor are only 1mm thick (as designed). The...

I remixed this to hold the iPad Mini. This will work with all generations of the mini. Make sure to print with supports everywhere. ...Print Settings Supports: Yes

Quick remix from another extender but works amazing! ...The extender works great with the Ipad pro with Case+Cover Printed with 30% infill.

I remixed this to hold the iPad Mini. This will work with all generations of the mini. ... Make sure to print with supports everywhere.

DJI Phantom 2 dummy motor, for testing/mockup purposes.

Gimbal Mount for DJI Phantom 2.  Known part which can break upon crashes.  

Case pour Galaxy note 2 pour DJI phantom standard. Pour faire la charnière si vous avez des anciennes boites de lunettes recupérez la dessus . ...Utiliser du velcro pour fixer les cotés Ajout d'une fixation pour radio de P3S

The ZenClip is a clip for the DJI Phantom 1 and 2 and Zenmuse H3-2D and H3-3D gimbal. It allows you to safely secure your gimbal while transporting your Phantom. ...The ZenClip requires a spring from a common clothes pin and a rubber band for added...

The ZenClip is a clip for the DJI Phantom 1 and 2 and Zenmuse H3-2D and H3-3D gimbal. It allows you to safely secure your gimbal while transporting your Phantom. ...The ZenClip requires a spring from a common clothes pin and a rubber band for added...

I made this cover for my DJI Phantom 2 battery, so we could go through customs. As airlines require that large capacity batteries terminals are covered, and I have a 3D printer, I made these. If you like this design or any of my others please...

This is a Gopro mount for Phantom 2 Instructions This was made in Google Sketchup

Parametrizable leg supplement for the Dji Phantom 2. Just edit the Open Scad source file and fill in your needs: height, cable gap, tolerance. Please note that the piece is not simmetric, so look for the correct position when mounting it in the...

I worked out this mod to have a nice enclosure to fit on the phantom 2, however, after finishing I noticed that it was not very comfortable for big batteries... Could be better to just take the smart board and drop it inside the phantom. Be extremely...

In Phantom 1 i had a door on hinges but Phantom 2 doesn't have those. There aren't many free (!) doors to choose from in internet so i have decided to make my own and this is what a came up with. Specification: - 2cm length, - almost...

... can vibrate loose. Everything should be printable without supports. Edit: It works with the Phantom 2 avionics as originally intended but mine has gradually evolved to have very little of the Phantom 2 left in it, more of a DIY f450-like drone.

It includes the cable twist-ons (you need to print two of the twist-ons, they screw into the mount) allowing you to tidy up the cabling between the glasses and your phone, and have it all click onto your phantom TX. ...

This is a great little iPad 2,3,4 holder to mount to your DJI Phantom 3 standard controller. This is based off a remix but removed support and rebuilt with watertight manifold so it's ready for slicing. Happy printing / flying :) Print Settings...