dji phantom 3 tablet holder 3d models
1052116 3d models found related to dji phantom 3 tablet holder.thingiverse
used the bracket made by markloane to make an adjustable tablet holder for my phantom controller. ...uses rubber springs on the back to keep tension on the tablet.
thingiverse
This is an tablet holder that works on the existing DJI phone holders. It's designed around an 7 inch tablet but I am sure the designconcept will work on other sizes as well. Have you printed my design? ...I would love to hear your opinion!
prusaprinters
This is an tablet holder that works on the existing DJI phone holders. It's designed around an 7 inch tablet but I am sure the designconcept will work on other sizes as well. Have you printed my design? ...I would love to hear your opinion! Print...
thingiverse
... a phone bracket so any phone can be fixed horizontally. ...Also reduced the width of the clamp and it still holds tablet and phone well without slippage. ...You can add some padding on the inside for better grip or use with tablet/iphone case also.
thingiverse
This will allow you to use larger tablets than an iPad or an iPad without taking the case off. ...Print Settings Printer Brand: Prusa Printer:...
thingiverse
The bottom clamp use the same 4 nuts to make it stationary, while the top clamp uses two wing nuts just on the top to tighten the clamp against the tablet. They do not need to be cranked down! Rods are available at Home Depot in 12 inch lengths, as...
thingiverse
I made this to fit a tablet on my Phantom 3 standard remote control without the shaky little arm. It has a 10mm opening for the tablet so I don't know what you have but you can use it and modify it as you want! good luck This thing was made with...
thingiverse
DJI Phantom 3 Gimbal Holder Unique Design I present my latest design 3D Printed 'Phantom 3 Gimbal Clamp with Lens Cap' The most important difference is there are no any loads on vibration dampers. It increase damper life through stability. You don't...
myminifactory
this is a holder for your phantom 3 batterys so you can mount them on the wall while charging use a little bit of support material under the spacer with the wall mount
thingiverse
you can plug in your phantom 3 battery with this or just use it to hold your battery on your wall Print Settings Printer: prusa i3 Rafts: No Supports: Yes Resolution: used .2 Infill: 5%
thingiverse
This will hold 3 screw on filters for the DJI Phantom 3. ... It should work with other models as well.
grabcad
The phantom drone 3 could only hold a small object like a phone, but the problem is that you can not see that much with just a phone. My teacher gave me a design project that could hold a tablet sized device and would fit firmly onto the drone...
thingiverse
Holder for the Phantom Vision 2 Plus and 3 Std/Adv/Pro You can simple snap'in the Tracker and remove it without Tools.
thingiverse
The holder can support a phone that is 3" wide up to a 5.5" wide phone or tablet. It will support a Ipad mini 7" tablet. Updated 2/18/2017 Add an adapter to allow smaller phones to fit. Will not fit a 2.25" to 5.5" wide phone or tablet. You will...
thingiverse
It did not fit my Dji phantom 3 standard. But i also liked "KhalidKhattak's" design with the possibility to add in a metal rod. All 3 models did not have a ability to acces the SD-card while the drone is not on. So i combined all 3 designs and made...
prusaprinters
It did not fit my Dji phantom 3 standard. But i also liked "KhalidKhattak's" design with the possibility to add in a metal rod. All 3 models did not have a ability to acces the SD-card while the drone is not on. So i combined all 3 designs and made...
pinshape
... is one of my older accessories for DJI FC40. ...This thing is useful when you want to use GoPro 3 (or 4?) as FC40 camera. Only pull out damping rubber and put it to this holder. Enjoy! Btw. ...on the image you can see original model form hard paper :)
pinshape
This is one of my older accessories for DJI FC40. ...This thing is useful when you want to use GoPro 3 (or 4?) as FC40 camera and supress jello effect. Only pull out damping rubber and put it to this holder. ... Enjoy!
thingiverse
Some dimensions were modified to handle small tablets and big phones. Holes were opened to allow faster printing and less drill bit cleanup. You need to print two clamps and one slider. The rods are #8-32, as well as the nuts. Using washers...
thingiverse
This thing is useful when you want to use GoPro 3 (or 4?) as FC40 camera and supress jello effect. Only pull out damping rubber and put it to this holder. Enjoy! Btw. on the image you can see original model form hard paper :) Edit: added lock for...
thingiverse
I have a DJI Phantom 3 drone, that has broken the SD card box. I can put the SD card, but it will not stay there (see picture 3). I called the service, and they said they need to change the full part. It is impossible to change only the SD-box. The...
thingiverse
I ordered the wrong filters (meant for Phantom 3 Pro/Adv) returning them is almost as costly as when I purchased them, therefore decided to design an adapter myself. Filters from PhantomFilters.com V1.0 ~ Idea was to lay the filter in the cup and...
sketchfab
This is a highly detailed version of the DJI Phantom 3 Pro for Element 3D Product Link: https://store.cgduck.pro/element-3d/dji-phantom-3-pro-e3d.html
sketchfab
Made DJI phantom 3 for online class. used 3ds max and painted with substance. ...hope you like guys.
myminifactory
Clamp for DJI Phantom 3 With this clamp you can attache using velcro tape some carriage. e.g. ...a such as a strobe light etc.
thingiverse
Kennzeichnungshalter für Drohne DJI Phantom 3 KENNZEICHENSCHILD bei www.3dcreativ.de in 40x20x1mm erhältlich. Besichtigung der Drohne mit Halter im Küstencamp. ... www.kuestencamp.de
thingiverse
It's a iPad 2 3 4 holder for Phantom Dji Standard. ...And it already has support Just print in 0.3, and cut out all the support